The Sun delivers about 1000 W of power on every square metre of ground on a clear day, and a solar cell turns part of that light straight into electricity with no moving parts, no fuel and no noise. This module of Physics for Emerging Fields explains how solar energy is converted into electricity, the photovoltaic effect and the working of a solar cell, the main types of solar cells, how cells are connected in series and parallel to build modules and arrays, and where solar systems are used. It maps to course outcome CO1 (measure solar power and construct a basic solar power system), and it links directly to the lab experiments on the V-I characteristics of a PV cell and on series and parallel combinations of cells.
Summary
Solar energy and its conversion to electricity: The Sun radiates energy produced by nuclear fusion. Just outside the Earth's atmosphere the power received on a surface facing the Sun is about 1361 W/m² (the solar constant). Part of it is absorbed and scattered by the atmosphere, so at ground level on a clear day around noon the irradiance is close to 1000 W/m², which is taken as the standard test value for solar panels. Solar energy can be converted into electricity in two main ways. In solar thermal power, mirrors concentrate sunlight to heat a fluid, the steam drives a turbine and a generator produces electricity (indirect conversion). In photovoltaic (PV) conversion, a semiconductor device called a solar cell converts light directly into electricity (direct conversion). PV is the method studied in this module because it is simple, modular and works from a few milliwatts (calculator) to hundreds of megawatts (solar parks).
Photovoltaic effect: The photovoltaic effect is the generation of a voltage (and a current in a closed circuit) across the junction of two different materials, usually a p-n junction, when light falls on it. It was first observed by Edmond Becquerel in 1839 in an electrolytic cell. It involves three steps: (i) absorption of a photon of energy \(h\nu \geq E_g\) creates an electron-hole pair; (ii) the built-in electric field of the depletion region separates the pair, pushing electrons to the n side and holes to the p side; (iii) this charge separation builds up a voltage across the junction, and if an external load is connected a current flows through it. Photons with energy less than the band gap pass through without creating pairs, and the extra energy of high-energy photons (above \(E_g\)) is lost as heat.
Construction of a solar cell: A typical crystalline silicon solar cell is a large-area p-n junction. A thick, lightly doped p-type silicon wafer (about 150 to 200 μm) forms the base. A very thin, heavily doped n-type layer (less than 1 μm) is diffused into its top surface so that light reaches the junction. The top surface has a thin grid of metal fingers and bus bars (front contact) so that most of the area stays open to light, while the back is fully covered with metal (back contact). An anti-reflection coating (for example silicon nitride) and a textured surface reduce reflection losses, and the cell is covered with toughened glass and sealed in a polymer (EVA) for protection.
Working of a solar cell: When sunlight falls on the cell, photons pass through the thin n layer and are absorbed near the junction. Each absorbed photon with \(h\nu \geq E_g\) creates an electron-hole pair. Pairs created in or within a diffusion length of the depletion region are separated by the built-in field: electrons drift to the n side and holes to the p side. The n side becomes negative and the p side positive, giving an open-circuit voltage of about 0.5 to 0.7 V for silicon. When a load is connected, electrons flow from the n side through the external circuit to the p side, where they recombine with holes. Current flows as long as light falls on the cell. The current is roughly proportional to the light intensity, while the voltage changes only slowly (logarithmically) with intensity.
Solar cell parameters: The V-I characteristic of an illuminated cell lies in the fourth quadrant of the diode curve and is usually drawn flipped to the first quadrant. The short-circuit current \(I_{sc}\) is the current when the terminals are shorted (V = 0); it is the largest current the cell can give. The open-circuit voltage \(V_{oc}\) is the voltage with no load (I = 0). Power is zero at both points, and it is maximum at one point on the knee of the curve, the maximum power point with voltage \(V_m\) and current \(I_m\). The fill factor \(FF = V_mI_m/(V_{oc}I_{sc})\) measures how square the curve is (about 0.7 to 0.85 for good cells). The conversion efficiency is \(\eta = P_{max}/P_{in} = FF\,V_{oc}I_{sc}/(G A)\), where G is the irradiance and A the cell area.
Types of solar cells: First-generation cells are made from silicon wafers: monocrystalline (single crystal, uniform dark colour, highest commercial efficiency about 20 to 24 percent) and polycrystalline or multicrystalline (many grains, bluish speckled look, cheaper, about 15 to 20 percent). Second-generation cells are thin films deposited on glass, metal or plastic: amorphous silicon (a-Si, cheap and flexible but low efficiency, about 6 to 10 percent, used in calculators), cadmium telluride (CdTe) and copper indium gallium selenide (CIGS). They use far less material but are usually less efficient than crystalline silicon. Third-generation and emerging cells aim at high efficiency or very low cost: multi-junction (tandem) cells made of stacked layers of different band gaps (for example GaInP/GaAs/Ge) that absorb different parts of the spectrum and exceed 40 percent under concentrated light (used in satellites), dye-sensitised solar cells (DSSC), organic solar cells and perovskite solar cells, whose laboratory efficiency has risen very fast.
Series and parallel connections: A single silicon cell gives only about 0.5 V at its maximum power point and a few amperes, so cells are joined to get useful voltage and current. In a series connection the positive of one cell is joined to the negative of the next: the voltages add, while the current is the same as that of one cell (and is limited by the weakest or shaded cell). In a parallel connection all positives are joined together and all negatives together: the currents add, while the voltage is that of one cell. Cells in series form a module (panel), for example 36 cells in series give about 21 V open circuit, suitable to charge a 12 V battery; modules are again connected in series to form a string and strings in parallel to form an array. Bypass diodes across cells or groups of cells let current flow around a shaded cell so that it does not block the whole string or overheat (hot spot). Blocking diodes in series with each string prevent current flowing back into a string or from the battery into the panel at night.
Solar power system and applications: A basic stand-alone (off-grid) system has a PV array, a charge controller (PWM or MPPT type, which keeps the array near its maximum power point and protects the battery), a battery bank, an inverter to convert DC into AC, and the loads. A grid-connected (on-grid) system feeds power to the utility grid through a grid-tie inverter, often with net metering, and needs no battery. A hybrid system has both. Applications include rooftop power for homes, offices and colleges, large solar parks, solar water pumps for agriculture, street lights and traffic signals, rural electrification, telecom towers, power for satellites and space stations, calculators, watches and portable chargers, solar charging of electric vehicles, and powering remote sensors and railway signalling.
Mind map
Solar Energy
- Conversion routes
- Solar thermal (indirect)
- Photovoltaic (direct)
- Irradiance about 1000 W/m²
- Photovoltaic effect
- Photon with hν ≥ Eg
- Electron-hole pair
- Separation by junction field
- Voltage and current
- Solar cell
- Thin n layer on p wafer
- Finger grid, back contact, ARC
- Isc, Voc, Vm, Im
- Fill factor, efficiency
- Types
- Mono and poly c-Si
- Thin film: a-Si, CdTe, CIGS
- Multi-junction, DSSC, organic, perovskite
- Connections
- Series: V adds, I same
- Parallel: I adds, V same
- Cell, module, string, array
- Bypass and blocking diodes
- Applications
- Off-grid, on-grid, hybrid
- Pumps, street lights, satellites
- Rooftop and solar parks
How a solar cell produces electricity
- Sunlight (photons of many energies) falls on the cell through the glass and anti-reflection coating.
- Photons with \(h\nu \geq E_g\) (for silicon \(E_g = 1.12\) eV, so wavelengths shorter than about 1.1 μm) are absorbed in the silicon.
- Each absorbed photon lifts an electron from the valence band to the conduction band, leaving a hole: an electron-hole pair is created.
- Pairs generated in the depletion region, or close enough to diffuse to it, feel the built-in field \(E_0\) that points from n to p.
- The field sweeps electrons into the n region and holes into the p region before they can recombine.
- Excess electrons collect on the n side (negative terminal, front grid) and excess holes on the p side (positive terminal, back contact): a photo-voltage \(V_{oc}\) appears.
- When a load is connected, electrons flow from the n side through the load to the p side, delivering power \(P = VI\).
- The operating point is chosen at the knee of the V-I curve (maximum power point) to get \(P_{max} = V_mI_m = FF\,V_{oc}I_{sc}\).
V-I characteristic and maximum power point
To draw the curve in the lab, the illuminated cell is connected to a variable load resistance with a voltmeter across it and an ammeter in series. As the resistance is increased from zero, the current stays almost constant near \(I_{sc}\) while the voltage rises, then near the knee the current falls sharply and the voltage approaches \(V_{oc}\). Plotting I against V gives a curve that is flat at the top and drops steeply at the right. Plotting P = VI against V gives a hill-shaped curve whose peak is the maximum power point. The rectangle \(V_m \times I_m\) is the largest rectangle that fits under the V-I curve, and the fill factor is the ratio of this rectangle to the rectangle \(V_{oc} \times I_{sc}\). The load resistance that gives maximum power is \(R_{opt} = V_m/I_m\). Increasing light intensity raises \(I_{sc}\) almost proportionally and \(V_{oc}\) only a little; increasing temperature lowers \(V_{oc}\) (by about 2 mV per °C per silicon cell) and so lowers the efficiency, which is why panels are kept ventilated.
Important definitions
| Term | Meaning |
|---|---|
| Solar constant | Solar power received per unit area on a surface normal to the Sun's rays just outside the Earth's atmosphere, about 1361 W/m². |
| Irradiance (G) | Solar power falling on unit area of a surface, in W/m²; about 1000 W/m² under standard test conditions. |
| Photovoltaic effect | Generation of a voltage and current across a junction of two materials (usually a p-n junction) when it is exposed to light. |
| Solar cell | A large-area p-n junction device that converts light energy directly into electrical energy by the photovoltaic effect. |
| Short-circuit current (Isc) | Current through the cell when its terminals are shorted, V = 0; the maximum current of the cell. |
| Open-circuit voltage (Voc) | Voltage across the cell when no current is drawn, I = 0; the maximum voltage of the cell. |
| Maximum power point | The point (Vm, Im) on the V-I curve at which the product VI is the largest. |
| Fill factor (FF) | Ratio of maximum power to the product Voc Isc; measures the squareness of the V-I curve. |
| Conversion efficiency (η) | Ratio of maximum electrical power output to the incident light power on the cell. |
| Module (panel) | A set of solar cells connected (mostly in series) and sealed in one weather-proof frame. |
| Array | A group of modules connected in series (strings) and parallel to give the required voltage and current. |
| Bypass diode | A diode connected in parallel (reverse direction) across a cell or group of cells that lets current pass around it when it is shaded. |
| Peak sun hours | Equivalent number of hours per day of 1000 W/m² sunshine that would give the same daily solar energy at a site. |
Formulas
| Formula | Meaning |
|---|---|
| \( h\nu \geq E_g,\ \ \lambda_c = \dfrac{hc}{E_g} \) | Condition for pair creation; cut-off wavelength above which light is not absorbed (λc in μm ≈ 1.24/Eg in eV). |
| \( P_{in} = G\,A \) | Incident solar power; G irradiance (W/m²), A area (m²). |
| \( FF = \dfrac{V_mI_m}{V_{oc}I_{sc}} \) | Fill factor. |
| \( P_{max} = V_mI_m = FF\,V_{oc}I_{sc} \) | Maximum output power of a cell or module. |
| \( \eta = \dfrac{P_{max}}{P_{in}} = \dfrac{FF\,V_{oc}I_{sc}}{G\,A} \) | Conversion efficiency. |
| \( V_{series} = N_sV,\ \ I_{series} = I \) | Ns identical cells in series. |
| \( I_{parallel} = N_pI,\ \ V_{parallel} = V \) | Np identical cells in parallel. |
| \( P_{array} = N_sN_p\,V_mI_m \) | Array of Np parallel strings, each of Ns cells or modules in series. |
| \( I = I_L - I_0\left(e^{eV/\eta kT} - 1\right) \) | Current of an illuminated cell; IL light-generated current, I0 dark saturation current. |
| \( V_{oc} = \dfrac{\eta kT}{e}\ln\left(\dfrac{I_L}{I_0} + 1\right) \) | Open-circuit voltage; grows only logarithmically with light. |
| \( E_{day} = P_{array} \times \text{peak sun hours} \) | Approximate daily energy from an array (before system losses). |
Key points to remember
- Solar cells convert light directly into electricity; solar thermal plants convert it via heat and a turbine.
- Only photons with \(h\nu \geq E_g\) create electron-hole pairs; for silicon the cut-off wavelength is about 1.1 μm.
- The built-in field of the depletion region separates the pairs; no external bias is applied to a solar cell.
- The top n layer is very thin so that light reaches the junction; the front contact is a grid of thin fingers.
- Isc is proportional to light intensity; Voc increases only logarithmically with intensity and falls with temperature.
- The V-I curve of a solar cell lies in the fourth quadrant of the diode characteristic.
- FF of good silicon cells is about 0.75 to 0.85; commercial module efficiency is about 18 to 23 percent.
- Monocrystalline is more efficient and costly; polycrystalline is cheaper; thin films use less material but are less efficient.
- Multi-junction cells use several band gaps to reduce thermal losses and give the highest efficiencies.
- Series: voltage adds, current same. Parallel: current adds, voltage same. Power adds in both cases.
- One shaded cell in a series string limits the string current; bypass diodes solve this problem.
- MPPT charge controllers keep the array at its maximum power point as light and temperature change.
Solved examples
Example 1. A silicon solar cell of area 100 cm² has Voc = 0.6 V and Isc = 3.2 A under 1000 W/m². At the maximum power point Vm = 0.5 V and Im = 3.0 A. Find the fill factor and efficiency.
\(P_{max} = V_mI_m = 0.5 \times 3.0 = 1.5\) W. \(FF = \dfrac{1.5}{0.6 \times 3.2} = \dfrac{1.5}{1.92} = 0.781\). Input power \(P_{in} = GA = 1000 \times 100\times10^{-4} = 10\) W. Efficiency \(\eta = 1.5/10 = 0.15 = 15\%\).
Example 2. A module has 36 identical cells in series. Each cell has Voc = 0.6 V, Isc = 3 A, Vm = 0.48 V and Im = 2.8 A. Find the module Voc, Isc and maximum power.
In series voltages add and current stays the same. \(V_{oc} = 36 \times 0.6 = 21.6\) V, \(I_{sc} = 3\) A, \(V_m = 36 \times 0.48 = 17.28\) V, \(I_m = 2.8\) A. \(P_{max} = 17.28 \times 2.8 = 48.4\) W (about a 48 W panel, suitable for charging a 12 V battery).
Example 3. Modules rated 18 V, 5 A at maximum power are available. Design an array that delivers 36 V and 20 A. How many modules are needed and what is the array power?
Modules in series per string \(N_s = 36/18 = 2\). Parallel strings \(N_p = 20/5 = 4\). Total modules \(= 2 \times 4 = 8\). Array power \(= 36 \times 20 = 720\) W, which also equals \(8 \times (18 \times 5) = 8 \times 90 = 720\) W.
Example 4. Find the longest wavelength of light that can generate electron-hole pairs in silicon (Eg = 1.12 eV).
\(\lambda_c = \dfrac{hc}{E_g} = \dfrac{6.63\times10^{-34}\times3\times10^{8}}{1.12\times1.6\times10^{-19}} = 1.11\times10^{-6}\) m \(= 1.11\) μm (near infrared). Light of longer wavelength passes through silicon without generating current.
Example 5. A house needs 2.4 kWh of electrical energy per day. The site gets 5 peak sun hours a day and the system losses (wiring, battery, inverter) are 20 percent. Find the array size and the number of 250 W panels.
Energy that one kW of panels gives per day after losses \(= 1 \times 5 \times 0.8 = 4\) kWh. Required array \(= 2.4/4 = 0.6\) kW \(= 600\) W. Number of 250 W panels \(= 600/250 = 2.4\), so 3 panels (750 W) must be installed, since panels come in whole numbers.
Example 6. A cell has light-generated current IL = 3 A and dark saturation current I0 = 10^-9 A at 300 K. Find Voc (take η = 1).
\(kT/e = 8.617\times10^{-5}\times300 = 0.02585\) V. \(V_{oc} = 0.02585\ln(3/10^{-9} + 1) = 0.02585 \times 21.82 = 0.564\) V. If the light is halved, IL = 1.5 A and Voc falls only by \(0.02585\ln2 = 0.018\) V, showing the logarithmic dependence.
Important questions and answers
Q1. Explain the photovoltaic effect. (3 marks)
When light of energy \(h\nu \geq E_g\) falls on a p-n junction, photons are absorbed and create electron-hole pairs near the junction. The built-in electric field of the depletion region (directed from n to p) separates them: electrons move to the n side and holes to the p side. Accumulation of negative charge on the n side and positive charge on the p side produces a voltage across the junction without any external source. If a load is connected, a current flows. This direct conversion of light into electrical energy is called the photovoltaic effect.
Q2. Describe the construction and working of a solar cell with a neat diagram. (5 marks)
Construction: a p-type silicon wafer forms the base; a thin heavily doped n-type layer is formed on top so that the junction is just below the surface; a metal finger grid on top and a full metal contact at the back collect the current; an anti-reflection coating covers the top; the cell is protected by glass. Diagram: layers from top: finger contacts, ARC, thin n layer, junction (depletion region), thick p layer, back metal contact, with light arrows falling on top and an external load connected between the top and back contacts. Working: photons absorbed near the junction create electron-hole pairs; the junction field drives electrons to the n side and holes to the p side; the n side becomes the negative terminal and the p side the positive terminal; Voc of about 0.6 V appears; with a load, current flows from p to n through the external circuit (electrons from n to p). The cell keeps working as long as light falls on it. Its output is described by Isc, Voc, FF and efficiency.
Q3. Draw and explain the V-I characteristic of a solar cell. Define fill factor and efficiency. (5 marks)
Draw current on the y axis and voltage on the x axis: the curve starts at \(I_{sc}\) on the current axis, stays nearly flat, bends at the knee and falls to zero at \(V_{oc}\) on the voltage axis. Mark the maximum power point (Vm, Im) at the knee and draw the largest rectangle under the curve. In the dark the cell behaves as an ordinary diode; under light the curve shifts down by \(I_L\) into the fourth quadrant, and it is drawn flipped for convenience. Fill factor \(FF = V_mI_m/(V_{oc}I_{sc})\), a measure of how close the curve is to an ideal rectangle. Efficiency \(\eta = V_mI_m/(GA)\), the ratio of maximum electrical output to incident light power. Higher series resistance or lower shunt resistance reduces FF and efficiency.
Q4. Compare monocrystalline, polycrystalline and thin film solar cells. (5 marks)
Monocrystalline: cut from a single silicon crystal (Czochralski ingot), uniform black look with rounded corners, highest commercial efficiency (about 20 to 24 percent), more expensive, good for limited roof space. Polycrystalline: cast from molten silicon with many grains, blue speckled look, square cells, lower efficiency (about 15 to 20 percent) due to grain boundaries, cheaper to make. Thin film (a-Si, CdTe, CIGS): a layer only a few micrometres thick deposited on glass, metal or plastic, uses very little material, can be flexible and light, performs better at high temperature and in diffuse light, but has lower efficiency, so needs more area per kW; CdTe and CIGS modules reach about 17 to 20 percent (research cells above 22 percent) while a-Si is about 6 to 10 percent.
Q5. What are multi-junction solar cells? Why are they more efficient? (3 marks)
A multi-junction (tandem) cell is a stack of two or more p-n junctions of different band gaps, the widest gap on top. The top cell absorbs high-energy (blue) photons, and lower-energy photons pass through to the cells below with smaller band gaps. Each photon is therefore absorbed in a cell whose band gap is close to its energy, so less energy is lost as heat and more of the spectrum is used. Such cells (for example GaInP/GaAs/Ge) give efficiencies above 40 percent under concentrated sunlight and are used in satellites and concentrator PV, though they are expensive.
Q6. Explain series and parallel connection of solar cells with diagrams. (5 marks)
Series: the positive terminal of each cell is joined to the negative of the next. Total voltage \(V = V_1 + V_2 + \dots\); current is the same through all cells and equals the current of the weakest cell. Used to raise the voltage, for example 36 cells to make a 12 V class module. Parallel: all positive terminals are connected together and all negative terminals together. Total current \(I = I_1 + I_2 + \dots\); voltage equals that of one cell. Used to raise the current. Series-parallel: strings of cells in series are connected in parallel to obtain both the required voltage and current, as in an array. In both connections the total power is the sum of the individual powers if the cells are identical. Mismatch and shading reduce output; bypass diodes across series cells and blocking diodes in each parallel string protect the array.
Q7. Why are bypass diodes used in a solar module? (3 marks)
When one cell in a series string is shaded, it produces little current, yet the other cells force the string current through it. The shaded cell becomes reverse biased, absorbs power instead of producing it and may overheat (hot spot), and it limits the current of the whole string. A bypass diode connected across the cell or a group of cells, in the reverse direction to normal flow, becomes forward biased in this situation and carries the string current around the shaded group. This protects the cells and keeps the rest of the module producing power.
Q8. Draw the block diagram of a stand-alone solar power system and explain each block. (5 marks)
Blocks in order: PV array, charge controller, battery bank, inverter, AC load (with a DC load taken from the controller if needed). PV array: converts sunlight into DC electricity. Charge controller: regulates the charging current and voltage, prevents overcharge and deep discharge of the battery; an MPPT controller also extracts maximum power from the array. Battery: stores energy for use at night and on cloudy days. Inverter: converts DC from the battery into 230 V, 50 Hz AC. Loads: lights, fans, pumps and appliances. In a grid-connected system the battery is omitted and a grid-tie inverter feeds surplus power to the grid.
Q9. List applications of solar energy systems. (3 marks)
Rooftop solar for homes, institutions and industries; utility-scale solar parks feeding the grid; solar water pumps for irrigation; street lights, traffic signals and highway signs; power for telecom towers and remote villages; satellites and space stations; calculators, watches, garden lights and mobile chargers; solar EV charging stations; powering wireless sensors, weather stations and railway signals; solar desalination and cold storage in remote places.
Exam tips
- In construction questions always label: finger grid, ARC, thin n layer, depletion region, p wafer, back contact and the external load.
- Write the three steps of the photovoltaic effect: absorption, separation by the junction field, collection.
- For the V-I curve mark Isc, Voc, Vm, Im and shade the maximum power rectangle; this earns most of the marks.
- In array numericals find modules in series from voltage and strings in parallel from current, then check power both ways.
- Always convert area to m² (1 cm² = 10^-4 m²) before finding efficiency.
- Round up the number of panels: you cannot install 2.4 panels.
- Remember λc (μm) ≈ 1.24/Eg (eV) for quick checks.
FAQs
Does a solar cell work on a cloudy day?
Yes, but with less output. Diffuse light still creates electron-hole pairs, so the current falls roughly in proportion to the reduced irradiance while the voltage drops only slightly.
Why is the efficiency of a single silicon cell limited to about 30 percent?
Photons below the band gap are not absorbed, and photons well above it waste their extra energy as heat. Together with unavoidable recombination, this limits a single-junction cell to roughly a third of the incident power even in theory.
Why do solar panels give less power on very hot days?
The open-circuit voltage of silicon cells falls by about 2 mV per °C per cell as temperature rises, so the maximum power drops by roughly 0.3 to 0.5 percent per °C above 25 °C.
Is a solar cell the same as a photodiode?
Both are p-n junctions that respond to light, but a photodiode is small, reverse biased and used to detect light, while a solar cell is large, unbiased and designed to deliver power to a load.
These notes follow the University of Mumbai first-year engineering syllabus (NEP 2020, Physics for Emerging Fields, Semester II) and were prepared with AI help and checked.