A gas-stove lighter makes a spark without a battery, and a wireless sensor on a bridge can run for years without anyone changing its cells. Both use energy harvesting: collecting small amounts of energy that are already present around us, such as vibration, pressure, motion, heat or light, and turning them into electricity. This module of Physics for Emerging Fields focuses on the piezoelectric route. It covers the piezoelectric effect, piezoelectric materials and the models used to describe them, the piezoelectric electricity generator, applications of energy harvesting, and human power (energy available from the human body). It maps to course outcome CO5 (assimilate the concept of energy harvesting and its role in eco-friendly applications) and to the lab experiment on a piezoelectric transducer as an energy source.
Summary
Energy harvesting: Energy harvesting (also called energy scavenging) is the process of capturing small amounts of ambient energy (mechanical vibration, motion, pressure, heat, light, radio waves) and converting it into electrical energy to power low-power electronics such as wireless sensors, wearables and implants. It is needed because modern sensor networks have millions of nodes in places where wiring is impossible and changing batteries is costly or dangerous. Sources and transducers: mechanical (piezoelectric, electromagnetic, electrostatic), thermal (thermoelectric generators using the Seebeck effect), light (photovoltaic), and RF (rectifying antennas). Harvested power is small, from microwatts to milliwatts, so the electronics must be ultra-low power and usually store the energy in a capacitor or rechargeable battery and use it in bursts.
Piezoelectric effect: The direct piezoelectric effect is the generation of electric charge (and hence a voltage) on the surfaces of certain crystals when they are mechanically stressed; the charge is proportional to the applied force and reverses sign when compression changes to tension. It was discovered by Pierre and Jacques Curie in 1880 in quartz, tourmaline and Rochelle salt. The converse (inverse) piezoelectric effect is the mechanical deformation (strain) of the crystal when an electric field is applied; it was predicted by Gabriel Lippmann in 1881 and confirmed by the Curies. Cause: piezoelectricity occurs only in crystals without a centre of symmetry. In such a crystal, stress displaces the positive and negative ions unequally, so the centres of positive and negative charge in each unit cell no longer coincide; tiny electric dipoles appear, and their sum gives a net polarisation and bound surface charges on opposite faces. Of the 32 crystal classes, 21 lack a centre of symmetry and 20 of these are piezoelectric. Energy harvesters use the direct effect; actuators, buzzers and ultrasonic transmitters use the converse effect.
Piezoelectric materials: (i) Natural single crystals: quartz (SiO2, very stable, low charge constant about 2.3 pC/N, used in oscillators), Rochelle salt, tourmaline. (ii) Synthetic crystals: lithium niobate, lithium tantalate, gallium phosphate. (iii) Ceramics: barium titanate (BaTiO3, d33 about 190 pC/N) and lead zirconate titanate (PZT, d33 about 300 to 600 pC/N), the most widely used harvester material because of its large coupling. Ceramics are polycrystalline and ferroelectric; after sintering their domains point randomly, so they must be poled by applying a strong DC field at an elevated temperature, which aligns the domains and makes them piezoelectric. They lose this property above their Curie temperature. Lead-free ceramics such as potassium sodium niobate (KNN) and bismuth sodium titanate are being developed because lead is toxic. (iv) Polymers: polyvinylidene fluoride (PVDF) and its copolymers, flexible, light and tough, with lower d33 (about 20 to 30 pC/N in magnitude), good for wearables and shoe inserts. (v) Thin films and nanostructures: zinc oxide (ZnO) nanowires, aluminium nitride (AlN), used in MEMS harvesters and nanogenerators. (vi) Composites of ceramic particles or fibres in a polymer (for example macro fibre composites) combine flexibility with high output.
Models for the piezoelectric effect: (a) Constitutive (linear piezoelectric) equations relate mechanical and electrical quantities: \(D = dT + \varepsilon^TE\) (direct effect) and \(S = s^ET + dE\) (converse effect), where D is electric displacement (charge per area), T stress, S strain, E electric field, d the piezoelectric charge coefficient, \(\varepsilon^T\) the permittivity at constant stress, and \(s^E\) the compliance at constant field. With no external field, the charge per unit area is \(D = dT\), so \(Q = dF\) for a force F on the electroded faces. (b) Coefficient notation and modes: \(d_{ij}\) gives the charge in direction i per unit stress in direction j, direction 3 being the poling axis. In the 33 mode the force and the electrodes are both along the poling axis (stacks, compression), giving a high coefficient. In the 31 mode the stress is perpendicular to the poling axis, as in a bending cantilever whose electrodes are on the top and bottom faces; d31 is smaller (about half of d33 and opposite in sign), but bending structures convert small forces into large strains, so the 31 mode is common in vibration harvesters. The voltage coefficient \(g = d/\varepsilon\) gives the open-circuit field per unit stress, and the electromechanical coupling factor \(k^2\) is the fraction of input mechanical energy converted to electrical energy (stored) in one cycle. (c) Electrical equivalent circuit: a piezoelectric element is modelled as a current (or charge) source in parallel with its internal capacitance \(C_p = \varepsilon A/t\) and a large leakage resistance, or equivalently a voltage source \(V = Q/C_p\) in series with \(C_p\). Near resonance a full Butterworth-Van Dyke model adds a series R-L-C branch representing damping, mass and stiffness. (d) Mechanical spring-mass-damper model: a vibration harvester (a cantilever with a tip mass) is modelled as a mass m on a spring of stiffness k with damping; when the base vibrates, the mass moves relative to the base and strains the piezoelectric layer. Output is largest when the vibration frequency equals the natural frequency \(f_n = \frac{1}{2\pi}\sqrt{k/m}\), so harvesters are tuned to the dominant ambient frequency (for example 50 to 120 Hz for machines and a few Hz for human motion), and maximum power is delivered when the load is matched to the source.
Piezoelectric electricity generator: A piezoelectric generator converts mechanical energy into electrical energy using the direct effect. Common configurations: (i) Cantilever (unimorph or bimorph): a metal beam carrying one or two piezoelectric layers is clamped at one end with a tip mass at the free end; vibration bends the beam, alternately stretching and compressing the layers and producing an AC voltage. (ii) Stack: many thin discs in series mechanically and in parallel electrically, compressed by a large force (33 mode), suited to roads, floors and heavy machines. (iii) Cymbal or diaphragm transducers that amplify force. (iv) Impact-type generators where a hammer or footstep strikes the element, as in a gas lighter (a spring-loaded hammer strikes a PZT crystal and produces several kilovolts across a spark gap). Power conditioning: the AC output is rectified by a diode bridge, stored in a capacitor or rechargeable battery, and regulated by a DC-DC converter before supplying the load; advanced circuits (synchronous switch harvesting) extract more energy. Output depends on the material coefficient, the strain, the frequency, the volume of material and load matching.
Energy harvesting applications: Wireless sensor nodes for structural health monitoring of bridges, buildings, pipelines and aircraft; machine condition monitoring using vibration of motors and pumps; tyre pressure monitoring sensors powered by tyre deformation; self-powered remote controls and light switches; floor tiles and road or railway installations that harvest footsteps and vehicle loads to light lamps or signs; wearable electronics and smart textiles; biomedical implants such as pacemakers powered by heartbeat or body motion (research stage); gas and cigarette lighters; low-power IoT devices in smart cities and agriculture. Benefits: no battery replacement, reduced chemical waste, maintenance-free operation in inaccessible places, eco-friendly and sustainable. Limitations: very low and intermittent power, frequency matching, fatigue of materials, and cost.
Human power: The human body is a large store and converter of energy. A resting adult dissipates roughly 100 W as heat (an order-of-magnitude estimate), and much more during activity. Sources that can be tapped: body heat (using thermoelectric generators; the small temperature difference with the surroundings limits output to a fraction of a watt), breathing (chest expansion), blood pressure, arm and leg motion, typing, and above all walking. During walking the heel strikes the ground about once per second for each foot, and the body weight compresses the shoe sole; the energy available per step is about mgh, where h is the compression, and estimates of the total power available from heel strike are of the order of tens of watts for a fast walk (an order-of-magnitude estimate; published figures vary widely with the assumptions made). Only a small part can be harvested without disturbing the walker: piezoelectric shoe inserts (PVDF or PZT) give milliwatts, enough for sensors, RFID tags or wearable devices; knee-mounted and backpack harvesters can give watts but add effort. Human power is classified as active (the user deliberately works, as in hand-crank radios, pedal generators and shake torches) or passive (energy is scavenged from normal activities like walking, breathing and body heat). It is attractive for wearables, health monitors and soldiers' equipment.
Mind map
Energy Harvesting
- Concept
- Ambient energy to electricity
- Vibration, heat, light, RF
- μW to mW for sensors
- Piezoelectric effect
- Direct: stress → charge
- Converse: field → strain
- Non-centrosymmetric crystals
- Curie brothers, 1880
- Materials
- Quartz, Rochelle salt
- BaTiO3, PZT (poled)
- PVDF polymer
- ZnO, AlN, composites
- Models
- D = dT + εE
- 33 and 31 modes
- Equivalent circuit: source + Cp
- Spring-mass-damper, resonance
- Generator
- Cantilever, stack, cymbal, impact
- Rectifier, storage, regulator
- Applications and human power
- Wireless sensors, TPMS, lighters
- Floor tiles, wearables, implants
- Heel strike, body heat, breathing
- Active and passive human power
From footstep to stored energy: how a piezoelectric harvester works
- A force F (footstep, vibration, impact) stresses a poled piezoelectric element, for example a PZT disc.
- The stress shifts the positive and negative ions unequally inside each unit cell, changing the dipole moment.
- A net polarisation appears and bound charges of opposite sign collect on the two electroded faces: \(Q = d_{33}F\).
- The element acts as a charged capacitor \(C_p = \varepsilon_0\varepsilon_rA/t\), so an open-circuit voltage \(V = Q/C_p\) appears.
- When the force is removed (or reversed) the charge reverses, so a vibrating element produces an AC voltage.
- A bridge rectifier converts the AC to DC, which charges a storage capacitor or battery.
- The energy delivered per press is at most \(\tfrac{1}{2}C_pV^2\); repeated presses add up the energy.
- A regulator supplies a steady voltage to a low-power load such as a sensor, LED or radio transmitter, which works in short bursts.
Important definitions
| Term | Meaning |
|---|---|
| Energy harvesting | Capturing small amounts of ambient energy (motion, heat, light, RF) and converting it to electricity for low-power devices. |
| Direct piezoelectric effect | Development of electric charge on a crystal when mechanical stress is applied. |
| Converse piezoelectric effect | Mechanical strain produced in a crystal when an electric field is applied. |
| Piezoelectric charge coefficient (d) | Charge produced per unit force (C/N), or strain per unit field (m/V). |
| Piezoelectric voltage coefficient (g) | Electric field produced per unit stress, g = d/ε (V m/N). |
| Electromechanical coupling factor (k) | k² is the fraction of mechanical energy converted into electrical energy (or vice versa) in the material. |
| Poling | Applying a strong DC field to a ferroelectric ceramic, usually while hot, to align its domains and make it piezoelectric. |
| Curie temperature | Temperature above which a piezoelectric ceramic loses its polarisation and piezoelectric property. |
| Unimorph / bimorph | A bending element with one / two piezoelectric layers bonded to a beam. |
| Resonant frequency | Natural frequency of the harvester at which it vibrates with largest amplitude and output. |
| Human power | Energy obtained from human activities or body processes such as walking, breathing and body heat. |
| Passive human power | Energy scavenged from normal activity without extra effort by the user. |
Formulas
| Formula | Meaning |
|---|---|
| \( D = dT + \varepsilon^TE,\ \ S = s^ET + dE \) | Linear constitutive equations of piezoelectricity. |
| \( Q = d_{33}F \) | Charge from a force F along the poling axis (33 mode). |
| \( C_p = \dfrac{\varepsilon_0\varepsilon_rA}{t} \) | Capacitance of a piezo element of area A and thickness t. |
| \( V = \dfrac{Q}{C_p} = \dfrac{d_{33}Ft}{\varepsilon_0\varepsilon_rA} \) | Open-circuit voltage. |
| \( g = \dfrac{d}{\varepsilon_0\varepsilon_r},\ \ V = g\,t\,\sigma \) | Voltage coefficient; σ = F/A is the stress. |
| \( W = \tfrac{1}{2}C_pV^2 = \dfrac{Q^2}{2C_p} \) | Electrical energy stored per press. |
| \( f_n = \dfrac{1}{2\pi}\sqrt{\dfrac{k}{m}} \) | Natural frequency of a spring-mass (cantilever) harvester. |
| \( E_{step} = mgh,\ \ P = E_{step} \times \text{steps per second} \) | Energy and power available from heel strike. |
| \( P_{avg} = W f \) | Average power from energy W harvested per cycle at f cycles per second. |
Key points to remember
- Direct effect: stress gives charge (generators, sensors). Converse effect: field gives strain (actuators, buzzers).
- Only non-centrosymmetric crystals are piezoelectric: 20 of the 32 crystal classes.
- Charge is proportional to force and reverses with the direction of stress.
- PZT has a much higher d than quartz; PVDF is flexible but weaker.
- Ceramics must be poled and must stay below their Curie temperature.
- 33 mode: compression along poling axis; 31 mode: bending with stress perpendicular to poling.
- A piezo element behaves like a charge source in parallel with a capacitor.
- Vibration harvesters give maximum output at resonance and with a matched load.
- The output is AC: rectify, store and regulate before use.
- Harvested power is microwatts to milliwatts: enough for sensors, not for heavy loads.
- Walking (heel strike) is the richest passive human power source; body heat and breathing give less.
Solved examples
Example 1. A quartz crystal (d = 2.3 pC/N) is pressed with a force of 100 N. Find the charge produced. If its capacitance is 10 pF, find the voltage.
\(Q = dF = 2.3\times10^{-12}\times100 = 2.3\times10^{-10}\) C \(= 230\) pC. \(V = Q/C = 2.3\times10^{-10}/10\times10^{-12} = 23\) V.
Example 2. A PZT disc of radius 1 cm and thickness 1 mm has d33 = 400 pC/N and εr = 1700. A 70 kg person stands on it (g = 9.8 m/s²). Find the charge, capacitance, voltage and energy.
\(F = 70\times9.8 = 686\) N. \(Q = 400\times10^{-12}\times686 = 2.744\times10^{-7}\) C \(= 274\) nC. \(A = \pi(0.01)^2 = 3.142\times10^{-4}\) m². \(C_p = \varepsilon_0\varepsilon_rA/t = 8.85\times10^{-12}\times1700\times3.142\times10^{-4}/10^{-3} = 4.73\times10^{-9}\) F \(= 4.73\) nF. \(V = Q/C_p = 2.744\times10^{-7}/4.73\times10^{-9} = 58.1\) V. \(W = \tfrac{1}{2}C_pV^2 = 0.5\times4.73\times10^{-9}\times58.1^2 = 7.97\times10^{-6}\) J \(\approx 8\) μJ per step, which shows why many elements and many steps are needed.
Example 3. For the same disc, find the voltage coefficient g33 and check the voltage using V = g t σ.
\(g_{33} = d_{33}/(\varepsilon_0\varepsilon_r) = 400\times10^{-12}/(8.85\times10^{-12}\times1700) = 0.0266\) V m/N. Stress \(\sigma = F/A = 686/3.142\times10^{-4} = 2.18\times10^{6}\) Pa. \(V = g\,t\,\sigma = 0.0266\times10^{-3}\times2.18\times10^{6} = 58.1\) V, the same as before.
Example 4. A 60 kg person walks at 2 steps per second and each step compresses the shoe sole by 1 cm. Find the power available from heel strike and the power harvested by a device of 5 percent efficiency.
Energy per step \(= mgh = 60\times9.8\times0.01 = 5.88\) J. Power available \(= 5.88\times2 = 11.76\) W (an order-of-magnitude estimate that assumes all of mgh per step could be captured). Harvested \(= 0.05\times11.76 = 0.59\) W. In practice shoe inserts harvest much less (milliwatts) so as not to make walking harder.
Example 5. A cantilever harvester has an effective stiffness of 200 N/m and an effective mass of 5 g. Find its resonant frequency.
\(f_n = \dfrac{1}{2\pi}\sqrt{\dfrac{200}{5\times10^{-3}}} = \dfrac{1}{2\pi}\sqrt{4\times10^{4}} = \dfrac{200}{2\pi} = 31.8\) Hz. It should be mounted where the ambient vibration is near 32 Hz.
Example 6. A harvester collects 8 μJ per cycle at 30 cycles per second. Find the average power. How long to store 10 mJ?
\(P = Wf = 8\times10^{-6}\times30 = 2.4\times10^{-4}\) W \(= 0.24\) mW. Time \(= 10\times10^{-3}/2.4\times10^{-4} = 41.7\) s, ignoring losses.
Important questions and answers
Q1. What is the piezoelectric effect? Explain its origin. (5 marks)
When certain crystals are mechanically stressed, equal and opposite charges appear on opposite faces; this is the direct piezoelectric effect. Conversely, when an electric field is applied they deform; this is the converse effect. Origin: in a crystal lacking a centre of symmetry, each unit cell contains positive and negative ions arranged so that at rest the centres of positive and negative charge coincide (or give a fixed polarisation). Applying stress distorts the cell and displaces the ions unequally, so the charge centres separate, creating an electric dipole in each cell. The dipoles add up to a polarisation P, whose bound charges appear on the surfaces normal to P, producing a voltage. The effect is linear (charge ∝ force) and reversible in sign. In centrosymmetric crystals the displacements cancel, so no polarisation results. Diagram: a hexagonal arrangement of Si and O ions in quartz shown unstressed and compressed, with + and − charges on opposite faces.
Q2. Discuss materials used for piezoelectric energy harvesting. (5 marks)
Natural crystals: quartz is stable and temperature-insensitive but has small d (about 2.3 pC/N); Rochelle salt is strong but water soluble. Ceramics: BaTiO3 (d33 about 190 pC/N) and PZT (300 to 600 pC/N) give high output; they are brittle, must be poled, have Curie temperatures that limit operation, and PZT contains lead, so lead-free KNN and BNT-based ceramics are being developed. Polymers: PVDF and P(VDF-TrFE) are flexible, light, impact resistant and biocompatible, suited to shoe inserts and wearables, but have lower coefficients. Thin films and nanostructures: AlN and ZnO for MEMS-scale harvesters and nanogenerators. Composites: ceramic fibres or particles in polymers combine flexibility and output. Selection depends on the coupling factor, d and g coefficients, flexibility, operating temperature, fatigue life and cost.
Q3. Explain the models used to describe a piezoelectric harvester. (5 marks)
(i) Constitutive equations \(D = dT + \varepsilon^TE\) and \(S = s^ET + dE\) link stress, strain, field and charge; for a free element in open circuit \(Q = dF\). (ii) Mode of operation: 33 mode with stress along the poling axis (stacks, high d) and 31 mode with stress perpendicular to it (bending beams, high strain from small forces). (iii) Electrical equivalent: a current source \(i = d\,dF/dt\) in parallel with the clamped capacitance Cp and leakage resistance, or a voltage source Q/Cp in series with Cp; near resonance a series RLC branch is added (Butterworth-Van Dyke model). (iv) Mechanical model: mass-spring-damper excited by base vibration, with natural frequency \(f_n = \frac{1}{2\pi}\sqrt{k/m}\); electrical damping from the load extracts energy. Maximum power is obtained at resonance with an optimum load resistance close to \(1/(2\pi fC_p)\).
Q4. Describe a piezoelectric electricity generator with a block diagram. (5 marks)
Mechanical source (vibration, footstep, impact) → piezoelectric transducer (cantilever bimorph with tip mass, stack or cymbal) → AC output → rectifier (diode bridge) → storage (capacitor or rechargeable battery) → DC-DC regulator → load (sensor node, LED, transmitter). The cantilever is clamped to a vibrating base; the tip mass lowers the resonant frequency to match the source; bending strains the piezo layers and generates charge alternately of each sign. A stack under a road or floor tile is compressed by passing loads. The circuit converts the irregular, high-impedance AC into a usable regulated DC supply. Example: a gas lighter, where a spring-loaded hammer strikes PZT to give a high-voltage spark.
Q5. Give applications of energy harvesting. (3 marks)
Self-powered wireless sensors for monitoring bridges, buildings, railways and machines; tyre pressure monitoring systems; batteryless switches and remote controls; footstep-powered floor tiles and lighting in stations; smart roads harvesting vehicle loads; wearables and fitness trackers; medical implants and hearing aids (research); lighters; IoT nodes in agriculture and smart cities. They save batteries, reduce maintenance and are environmentally friendly.
Q6. Write a note on human power. (5 marks)
The human body converts food energy and dissipates about 100 W at rest. Sources: body heat (thermoelectric generators on skin, limited by small temperature differences), breathing (chest band), blood pressure, upper limb motion, finger motion while typing, and walking (heel strike and knee motion), which offers the most power. Energy per step is roughly mgh, so a person of 60 to 70 kg walking briskly has, as an order-of-magnitude estimate, several watts or more available, of which piezoelectric shoe inserts recover milliwatts and knee harvesters a few watts. Types: active (hand-crank or pedal generators, shake flashlights, where the user works deliberately) and passive (scavenging normal activity). Uses: powering wearables, health sensors, GPS trackers and emergency radios. Challenges: low power, irregular motion, comfort and added effort.
Q7. Why are ceramics poled? (3 marks)
A sintered ceramic such as PZT consists of many grains, each containing domains with spontaneous polarisation in random directions, so the net polarisation is zero and no piezoelectric response is seen. Poling applies a strong DC field (a few kV/mm) at an elevated temperature below the Curie point; domains rotate towards the field and remain largely aligned after cooling. The ceramic then has a net polarisation and becomes strongly piezoelectric. Heating above the Curie temperature or applying a large reverse field depoles it.
Exam tips
- Define both direct and converse effects; mention non-centrosymmetric crystals and the Curie brothers.
- List materials under headings (crystals, ceramics, polymers, thin films, composites) with one property each.
- Draw a cantilever harvester with clamp, piezo layers, tip mass and electrodes, plus the block diagram of the power circuit.
- In numericals convert pC/N and area properly; use Cp = ε0εrA/t and V = Q/Cp, then W = ½CV².
- For human power give numbers per step (mgh) and note that only a small fraction can be harvested.
FAQs
Can piezoelectric tiles power a city?
No. Each step gives only a few joules at best, and harvesters capture a small part of that. Such tiles are useful for lighting signs or powering sensors, not for bulk power.
Why does a piezoelectric element give a high voltage but tiny current?
The generated charge is small and the element has a small capacitance, so V = Q/C is high, but the total energy and the current through any load are very small.
What is the difference between piezoelectric and electromagnetic harvesters?
Piezoelectric harvesters use strained crystals and give high voltage with low current, and they are easy to miniaturise. Electromagnetic harvesters move a magnet relative to a coil and give low voltage with higher current, working well at larger sizes.
Do piezoelectric materials wear out?
Ceramics can crack under repeated large strains, and they depole if overheated or over-driven, so harvesters are designed to keep strain and temperature within safe limits.
These notes follow the University of Mumbai first-year engineering syllabus (NEP 2020, Physics for Emerging Fields, Semester II) and were prepared with AI help and checked.