Skip to content
doubtly

Alloys Notes FE Sem 2 Engineering Materials | MU

Doubtly 17 min read Updated 27 Oct 2026 Save WhatsApp Save as PDF
On this page

Pure metals are rarely used as they are: pure iron is soft, pure copper is weak and pure aluminium is easily dented. Mixing a metal with small amounts of other elements produces an alloy whose hardness, strength, corrosion resistance or melting point is far better suited to a job. This module covers ferrous alloys (plain-carbon steels, heat and shock resisting steels and stainless steels) and the effect of the alloying elements Ni, Cr, Co, Mn, Mo, W and V, then the important non-ferrous alloys of aluminium (duralumin, magnalium), copper (Dutch metal, German silver, gun metal, nickel bronze) and lead (Wood's metal, tinman's solder), and finally numericals on the composition, density and weight of an alloy. It maps to course outcome CO1, and a composition-properties-uses question plus a short numerical appear in almost every paper.

Summary

Alloys and why we make them: An alloy is a metallic material made of two or more elements, at least one of which is a metal, mixed in the molten state and allowed to solidify. Alloying is done to increase hardness and tensile strength, to improve resistance to corrosion and oxidation, to lower the melting point (solders, fusible alloys), to improve castability and machinability, to change colour (imitation gold) and to obtain special electrical or magnetic properties. Alloys are classified as ferrous (iron as the main metal, for example steels) and non-ferrous (no iron as the base, for example brass, bronze, duralumin).

Plain-carbon steels: These are alloys of iron with up to about 1.5 percent carbon and only small amounts of Mn, Si, S and P left from steel making. As carbon increases, hardness and tensile strength increase but ductility, toughness and weldability fall. Low-carbon or mild steel (up to about 0.25 percent C) is soft, ductile and easily welded, and is used for wires, sheets, nails, pipes, car bodies and structural sections. Medium-carbon steel (about 0.25 to 0.6 percent C) is stronger and is used for rails, axles, shafts, gears and crankshafts. High-carbon steel (about 0.6 to 1.5 percent C) is hard and wear resistant and is used for springs, cutting tools, chisels, drills, files and razor blades.

Heat resisting steels: These steels keep their strength and resist oxidation (scaling) and creep at high temperatures. They contain a high percentage of chromium (roughly 12 to 30 percent), often with nickel and small amounts of Si, Mo or W. Chromium forms a thin, adherent Cr2O3 film that stops further oxidation, and Mo and W raise the high-temperature strength. They are used for furnace parts, boiler and heat-exchanger tubes, exhaust valves of engines, gas-turbine parts and retorts.

Shock resisting steels: These steels are made to absorb sudden impact without cracking, so they need high toughness together with reasonable hardness. They are low to medium carbon steels alloyed with elements such as Ni, Cr, Mo, Si and Mn (nickel gives toughness, silicon and molybdenum give strength). They are used for chisels, punches, hammers, pneumatic tools, rivet sets, shear blades and parts subjected to repeated impact.

Stainless steels: Stainless steels contain at least about 11 to 12 percent chromium (commonly 12 to 30 percent), which forms a self-healing passive Cr2O3 film, so they do not rust in air and water. Martensitic stainless steels (12 to 18 percent Cr, 0.1 to 1.2 percent C) can be hardened by heat treatment, are magnetic and are used for cutlery, surgical instruments, scissors and turbine blades. Ferritic stainless steels (about 12 to 30 percent Cr, low carbon) are magnetic, cannot be hardened by heat treatment and are used for automobile trim, kitchen sinks and chemical equipment. Austenitic stainless steels, the most common being 18/8 stainless steel (18 percent Cr, 8 percent Ni, carbon below about 0.15 percent), are non-magnetic, very ductile and have the best corrosion resistance; they are used for utensils, food and dairy plants, chemical plants, hospital equipment and architecture.

Effect of alloying elements: Nickel increases toughness, strength and corrosion resistance and keeps steel austenitic; chromium increases hardness, wear resistance and resistance to corrosion and oxidation; cobalt helps steel keep its hardness at high temperature and improves magnetic properties; manganese removes sulphur and oxygen and raises hardness and wear resistance; molybdenum increases high-temperature strength, creep resistance and hardenability and reduces temper brittleness; tungsten gives red hardness (hardness at red heat) needed for high-speed cutting tools; vanadium refines grain size and increases toughness, fatigue strength and hardness.

Aluminium alloys: Duralumin (about 95 percent Al, 4 percent Cu, 0.5 percent Mg, 0.5 percent Mn) is light yet nearly as strong as mild steel after heat treatment (age hardening), is ductile, machinable and a good conductor, and is used for aircraft and automobile bodies, surgical and orthopaedic instruments, cables and pressure-cooker parts. Magnalium (Al with Mg, engineering grades about 90 to 95 percent Al and 5 to 10 percent Mg) is lighter than aluminium and stronger, has better corrosion resistance and good machinability, and is used for aircraft and automobile parts, balance beams, light instruments and scientific apparatus; high-Mg magnalium powders are used in fireworks.

Copper alloys: Brass is copper plus zinc. Dutch metal (about 80 percent Cu, 20 percent Zn) is golden yellow, very malleable and is beaten into thin leaves as imitation gold for decoration, cheap jewellery and artificial gold leaf. German silver or nickel silver (commonly about 50 percent Cu, 25 percent Zn, 25 percent Ni; textbooks give ranges of 25 to 60 percent Cu, 10 to 35 percent Zn, 5 to 35 percent Ni) contains no silver but looks silvery white, resists corrosion and is used for utensils, decorative articles, coins, keys, zip fasteners, musical instruments and electrical resistance wire. Bronze is copper plus tin. Gun metal (88 percent Cu, 10 percent Sn, 2 percent Zn) is hard, strong, tough and resistant to sea water, and is used for gears, bearings, valves, pump parts, marine fittings and castings; it was once used for guns. Nickel bronze is a tin bronze containing a few percent nickel, which increases strength (especially at higher temperatures), hardness and corrosion resistance; it is used for valves and fittings, gears, bearings and marine parts.

Lead alloys: Wood's metal (50 percent Bi, 25 percent Pb, 12.5 percent Sn, 12.5 percent Cd) is a fusible alloy that melts at about 70 °C, below the boiling point of water. It is used in automatic fire sprinklers and fire alarms, fuse plugs and safety plugs of boilers, and for making casts. Tinman's solder (fine solder, about 63 percent Sn and 37 percent Pb; some books give 66 Sn : 34 Pb) melts sharply at about 183 °C, wets metals well and is used for soldering tin cans, electrical and electronic joints, radiators and sheet metal work. Lead-based alloys are toxic, so lead-free solders are now preferred for food and drinking water applications.

Numericals: Alloy numericals use the percentage composition by mass. The mass of each metal in a given mass of alloy is (percent/100) x total mass. If the volumes of the metals add up, the density of the alloy is found from \(1/\rho_{alloy} = \sum w_i/\rho_i\), where \(w_i\) is the mass fraction and \(\rho_i\) the density of each metal.

Mind map

Alloys

  • Ferrous alloys
    • Plain-carbon steel: low, medium, high C
    • Heat resisting steel: high Cr, Ni
    • Shock resisting steel: tough, Ni-Cr-Mo / Si-Mn
    • Stainless steel: at least about 12% Cr
    • Martensitic, ferritic, austenitic (18/8)
  • Alloying elements
    • Ni: toughness, corrosion resistance
    • Cr: hardness, oxidation resistance
    • Co: hot hardness, magnetism
    • Mn: deoxidiser, wear resistance
    • Mo: creep strength, no temper brittleness
    • W: red hardness
    • V: fine grain, toughness
  • Aluminium alloys
    • Duralumin: Al-Cu-Mg-Mn
    • Magnalium: Al-Mg
  • Copper alloys
    • Brass: Dutch metal, German silver
    • Bronze: gun metal, nickel bronze
  • Lead alloys
    • Wood's metal: melts about 70 °C
    • Tinman's solder: Sn-Pb, about 183 °C
  • Numericals
    • Mass of each metal
    • Density by mixture rule

Effect of alloying elements on steel

This is the most frequently asked theory part of the module. Learn each element with two or three effects and one example steel.

ElementEffect on properties of steelExample / use
Nickel (Ni)Increases toughness, tensile strength and ductility; improves corrosion resistance; stabilises austenite (makes steel non-magnetic at high Ni); lowers the critical (hardening) temperature.18/8 stainless steel, nickel steels for gears and shafts, invar (36% Ni) with almost zero expansion.
Chromium (Cr)Increases hardness, strength and wear resistance; forms a protective Cr2O3 film giving corrosion and oxidation resistance; increases hardenability.Stainless and heat resisting steels, ball bearings, chrome-vanadium tools.
Cobalt (Co)Helps steel keep its hardness at high temperature (hot hardness); improves magnetic properties (high remanence).Super high-speed steels, permanent magnet steels.
Manganese (Mn)Acts as deoxidiser and desulphuriser (forms MnS instead of brittle FeS); increases hardness, strength, hardenability and wear resistance.Hadfield manganese steel (12 to 14% Mn) for rock crushers, rail crossings, excavator teeth.
Molybdenum (Mo)Increases high-temperature strength and creep resistance; increases hardenability; reduces temper brittleness; improves red hardness.Heat resisting steels, high-speed steels, boiler and turbine parts.
Tungsten (W)Forms very hard carbides; gives red hardness, so tools keep their edge at high cutting speeds; increases wear resistance.High-speed steel 18-4-1 (18% W, 4% Cr, 1% V), cutting tools, drills.
Vanadium (V)Refines grain size; increases toughness, fatigue resistance and hardness; strong carbide former; improves resistance to softening on tempering.Chrome-vanadium spanners and springs, high-speed steels.

Types of stainless steel

TypeTypical compositionPropertiesUses
Martensitic12 to 18% Cr, 0.1 to 1.2% CHardenable by heat treatment, magnetic, fair corrosion resistanceCutlery, surgical instruments, scissors, springs, turbine blades
FerriticAbout 12 to 30% Cr, low C (below about 0.2%)Not hardenable by heat treatment, magnetic, good resistance to oxidation, cheaper (little or no Ni)Automobile trim, kitchen sinks, exhaust systems, chemical equipment
Austenitic (18/8)About 18% Cr, 8% Ni, C below about 0.15%Non-magnetic, very ductile and tough, best corrosion resistance, hardened only by cold workingUtensils, food and dairy plants, chemical plants, hospital equipment, architectural work

Non-ferrous alloys at a glance

AlloyComposition (by mass)PropertiesUses
DuraluminAl about 95%, Cu 4%, Mg 0.5%, Mn 0.5%Light (density about 2.8 g/cm³), high strength after age hardening, ductile, machinable, good conductor; lower corrosion resistance than pure AlAircraft structures, automobile parts, surgical instruments, cables, pressure cookers
MagnaliumAl about 90 to 95%, Mg 5 to 10%Lighter and stronger than Al, good corrosion resistance, easily machined and castAircraft and automobile parts, balance beams, light scientific instruments; high-Mg grades in fireworks
Dutch metal (brass)Cu about 80%, Zn 20%Golden colour, very malleable, can be beaten into thin foilImitation gold leaf, decorative articles, cheap jewellery
German silver (nickel silver)Typically Cu 50%, Zn 25%, Ni 25% (ranges vary)Silvery white, hard, corrosion resistant, high electrical resistanceUtensils, ornaments, coins, keys, zip fasteners, resistance coils, musical instruments
Gun metal (bronze)Cu 88%, Sn 10%, Zn 2%Hard, strong, tough, wear and sea-water corrosion resistant, casts wellGears, bearings, valves, pump parts, marine fittings
Nickel bronzeTin bronze with a few percent Ni (for example about 85 to 90% Cu, 5 to 10% Sn, 2 to 6% Ni)Higher strength, hardness and corrosion resistance than plain bronzeValves, fittings, gears, bearings, marine parts
Wood's metalBi 50%, Pb 25%, Sn 12.5%, Cd 12.5%Fusible, melts at about 70 °CFire sprinklers, fire alarms, fuse plugs, boiler safety plugs, casts
Tinman's solderAbout Sn 63%, Pb 37%Low and sharp melting point (about 183 °C), wets metals wellSoldering tin cans, electrical and electronic joints, sheet metal work

Important definitions

TermMeaning
AlloyA homogeneous metallic material made by mixing two or more elements, at least one a metal, in the molten state.
Ferrous alloyAn alloy whose main constituent is iron, for example steel.
Non-ferrous alloyAn alloy in which iron is not the main constituent, for example brass, bronze, duralumin.
Plain-carbon steelAn alloy of iron with up to about 1.5% carbon and no deliberately added alloying elements.
Alloy steelSteel to which elements such as Ni, Cr, Mo, W or V are added to obtain special properties.
Stainless steelAlloy steel containing at least about 11 to 12% chromium that resists rusting because of a passive chromium oxide film.
Heat resisting steelSteel that keeps its strength and resists oxidation and creep at high temperatures.
Shock resisting steelTough steel able to withstand sudden impact loads without cracking.
Red hardnessThe ability of a tool steel to keep its hardness at red heat (about 600 °C).
Fusible alloyAn alloy with a very low melting point, for example Wood's metal.
SolderA low melting alloy used to join metal parts without melting the parts themselves.
Brass and bronzeBrass is a copper-zinc alloy; bronze is a copper-tin alloy.

Formulas

FormulaMeaning
\( m_i = \dfrac{\%_i}{100}\times m_{alloy} \)Mass of component i in a given mass of alloy.
\( w_i = \dfrac{m_i}{\sum m_i} \)Mass fraction of component i.
\( \dfrac{1}{\rho_{alloy}} = \sum \dfrac{w_i}{\rho_i} \)Density of the alloy assuming the volumes of the metals add up.
\( V = \dfrac{m}{\rho} \)Volume of a given mass of metal or alloy.
\( \text{mole}\% \ \text{of } i = \dfrac{w_i/M_i}{\sum w_j/M_j}\times100 \)Converting mass percent to atom (mole) percent using atomic masses M.

Key points to remember

  • Carbon raises hardness and strength of steel but lowers ductility and weldability.
  • Stainless steel needs at least about 11 to 12% Cr; 18/8 means 18% Cr and 8% Ni.
  • Austenitic stainless steel is non-magnetic; martensitic and ferritic are magnetic.
  • Cr gives corrosion and oxidation resistance; Ni gives toughness; W and Mo give red hardness; V refines grain; Mn removes sulphur; Co keeps hardness hot.
  • High-speed steel 18-4-1: 18% W, 4% Cr, 1% V.
  • Duralumin: Al 95, Cu 4, Mg 0.5, Mn 0.5; light and strong, for aircraft.
  • Brass = Cu + Zn; bronze = Cu + Sn.
  • Dutch metal 80 Cu : 20 Zn; gun metal 88 Cu : 10 Sn : 2 Zn.
  • German silver contains no silver: it is Cu + Zn + Ni.
  • Wood's metal: Bi 50, Pb 25, Sn 12.5, Cd 12.5; melts at about 70 °C.
  • Density of an alloy: add mass fraction divided by density, then take the reciprocal; do not simply average the densities.

Solved examples

Example 1. Find the mass of each metal in 500 g of gun metal.

Gun metal: Cu 88%, Sn 10%, Zn 2%. Cu = 0.88 x 500 = 440 g; Sn = 0.10 x 500 = 50 g; Zn = 0.02 x 500 = 10 g. Check: 440 + 50 + 10 = 500 g.

Example 2. How much of each metal is needed to make 200 g of Wood's metal?

Bi = 0.50 x 200 = 100 g; Pb = 0.25 x 200 = 50 g; Sn = 0.125 x 200 = 25 g; Cd = 0.125 x 200 = 25 g.

Example 3. How much zinc must be melted with 400 g of copper to make Dutch metal (80% Cu, 20% Zn)?

Copper is 80% of the alloy, so mass of alloy = 400/0.80 = 500 g. Zinc = 500 - 400 = 100 g.

Example 4. A brass contains 60% Cu and 40% Zn by mass. Find its density (Cu = 8.96 g/cm³, Zn = 7.14 g/cm³) and the volume of 1 kg of this brass.

\( \dfrac{1}{\rho} = \dfrac{0.60}{8.96} + \dfrac{0.40}{7.14} = 0.06696 + 0.05602 = 0.12299 \) cm³/g, so \( \rho = 8.13 \) g/cm³. Volume of 1000 g = 1000/8.13 = 123.0 cm³.

Example 5. Find the density of German silver with 50% Cu, 25% Zn and 25% Ni (densities 8.96, 7.14 and 8.91 g/cm³).

\( \dfrac{1}{\rho} = \dfrac{0.50}{8.96} + \dfrac{0.25}{7.14} + \dfrac{0.25}{8.91} = 0.05580 + 0.03501 + 0.02806 = 0.11888 \), so \( \rho = 8.41 \) g/cm³.

Example 6. Duralumin contains 95% Al, 4% Cu, 0.5% Mg and 0.5% Mn. Find its density (Al 2.70, Cu 8.96, Mg 1.74, Mn 7.21 g/cm³).

\( \dfrac{1}{\rho} = \dfrac{0.95}{2.70} + \dfrac{0.04}{8.96} + \dfrac{0.005}{1.74} + \dfrac{0.005}{7.21} = 0.35185 + 0.00446 + 0.00287 + 0.00069 = 0.35988 \), so \( \rho = 2.78 \) g/cm³, only slightly more than pure aluminium even though it is far stronger.

Example 7. A Cu-Zn alloy has a density of 8.50 g/cm³. Find its percentage composition (Cu 8.96, Zn 7.14 g/cm³).

Let the mass fraction of Cu be w. Then \( \dfrac{1}{8.50} = \dfrac{w}{8.96} + \dfrac{1-w}{7.14} \). So \( 0.11765 = 0.14006 - w(0.14006 - 0.11161) \), giving \( w = 0.02241/0.02845 = 0.788 \). The alloy is about 78.8% Cu and 21.2% Zn.

Example 8. Convert 70% Cu, 30% Zn (by mass) brass into atom percent (Cu = 63.55, Zn = 65.38).

Moles in 100 g: Cu = 70/63.55 = 1.1015; Zn = 30/65.38 = 0.4589; total 1.5604. Atom % Cu = 1.1015/1.5604 x 100 = 70.6%; Zn = 29.4%.

Important questions and answers

Q1. Explain the effect of the alloying elements Ni, Cr, Co, Mn, Mo, W and V on the properties of steel. (5 marks)

Ni: increases toughness, strength, ductility and corrosion resistance, stabilises austenite (18/8 stainless steel). Cr: increases hardness, wear resistance and hardenability, and forms a Cr2O3 film giving corrosion and oxidation resistance (stainless and heat resisting steels). Co: retains hardness at high temperature and improves magnetic properties (high-speed and magnet steels). Mn: deoxidises and desulphurises (forms MnS), increases hardness and wear resistance (Hadfield steel, 12 to 14% Mn). Mo: increases high-temperature strength and creep resistance, increases hardenability and prevents temper brittleness. W: forms hard carbides and gives red hardness for high-speed tools (18-4-1 HSS). V: refines grain, increases toughness and fatigue resistance, and resists softening on tempering (chrome-vanadium tools).

Q2. What are stainless steels? Describe their types with properties and uses. (5 marks)

Stainless steels are alloy steels with at least about 11 to 12% chromium. Chromium forms a thin, invisible, self-healing Cr2O3 layer that protects the steel from rusting. Types: (i) Martensitic (12 to 18% Cr, 0.1 to 1.2% C): hardenable, magnetic; cutlery, surgical instruments, blades. (ii) Ferritic (12 to 30% Cr, low C): not hardenable, magnetic, good oxidation resistance; automobile trim, sinks, chemical equipment. (iii) Austenitic or 18/8 (18% Cr, 8% Ni, low C): non-magnetic, ductile, best corrosion resistance; utensils, food and dairy equipment, chemical plants, hospital equipment.

Q3. Write the composition, properties and uses of duralumin and magnalium. (5 marks)

Duralumin: Al about 95%, Cu 4%, Mg 0.5%, Mn 0.5%. Properties: light, high tensile strength after heat treatment (age hardening), ductile and malleable, machinable, good electrical conductor, less corrosion resistant than pure Al. Uses: aircraft frames and skins, automobile parts, surgical instruments, cables, pressure-cooker bodies. Magnalium: Al 90 to 95%, Mg 5 to 10%. Properties: lighter than Al, stronger and harder, good corrosion resistance, good machinability and castability. Uses: aircraft and automobile components, balance beams, light instruments; Mg-rich grades in fireworks.

Q4. Give the composition, properties and uses of Dutch metal and German silver. (4 marks)

Dutch metal: Cu about 80%, Zn 20%; golden yellow, very malleable, can be beaten into thin leaves; used as imitation gold leaf, decorative work, cheap jewellery. German silver: commonly Cu 50%, Zn 25%, Ni 25%; silvery white, hard, corrosion resistant, high electrical resistance; used for utensils, ornaments, coins, keys, zip fasteners, resistance wires and musical instruments. It contains no silver; the name comes from its colour.

Q5. Write the composition, properties and uses of gun metal and nickel bronze. (4 marks)

Gun metal: Cu 88%, Sn 10%, Zn 2%; hard, strong, tough, resistant to wear and sea-water corrosion, good casting alloy; used for gears, bearings, valves, pumps, marine fittings. Nickel bronze: copper-tin bronze with a few percent nickel; nickel raises strength (also at higher temperature), hardness and corrosion resistance; used for valves, fittings, gears, bearings and marine parts.

Q6. Write a note on Wood's metal and tinman's solder. (4 marks)

Wood's metal: Bi 50%, Pb 25%, Sn 12.5%, Cd 12.5%; melts at about 70 °C (below the boiling point of water); used in automatic fire sprinklers (the plug melts in a fire and releases water), fire alarms, fuse and safety plugs of boilers, and for making casts. Tinman's solder: about Sn 63%, Pb 37%; melts at about 183 °C, flows and wets metals well; used to solder tin plate, cans, electrical and electronic joints and sheet metal. Both contain toxic metals and must be handled with care.

Q7. What are heat resisting and shock resisting steels? (3 marks)

Heat resisting steels contain high Cr (about 12 to 30%) with Ni and some Si, Mo or W; they resist oxidation and creep and keep strength at high temperature; used in furnaces, boiler tubes, exhaust valves and turbine parts. Shock resisting steels are tough low to medium carbon steels containing Ni, Cr, Mo or Si and Mn; they absorb impact without cracking; used for chisels, punches, hammers and pneumatic tools.

Q8. Classify plain-carbon steels and give their uses. (3 marks)

Low carbon (mild) steel, up to about 0.25% C: wires, sheets, nails, pipes, structural sections. Medium carbon steel, about 0.25 to 0.6% C: rails, axles, shafts, gears. High carbon steel, about 0.6 to 1.5% C: springs, cutting tools, files, chisels, razor blades. Hardness and strength increase, and ductility decreases, with carbon content.

Q9. Calculate the density of an alloy containing 88% Cu, 10% Sn and 2% Zn (Cu 8.96, Sn 7.31, Zn 7.14 g/cm³). (3 marks)

\( 1/\rho = 0.88/8.96 + 0.10/7.31 + 0.02/7.14 = 0.09821 + 0.01368 + 0.00280 = 0.11470 \), so \( \rho = 8.72 \) g/cm³.

Exam tips

  • Prepare one compact table: alloy, composition, two properties, two uses. Most alloy questions can be answered from it.
  • When asked about an alloying element, write at least two effects and one example steel.
  • Always write percentages with the symbol of each metal, and check that they add up to 100.
  • In density numericals use the reciprocal (mixture) rule and give the answer in g/cm³ to two or three decimal places.
  • If a question gives a different composition from these notes, use the values given in the question.
  • Do not confuse German silver (Cu-Zn-Ni) with silver, or gun metal (a bronze) with steel.

FAQs

Why does stainless steel not rust?

Its chromium reacts with oxygen to form a very thin, continuous Cr2O3 layer. The layer blocks air and water from the iron underneath and re-forms quickly if scratched.

Why is the density of an alloy not the simple average of the metal densities?

Percentages are by mass, but volumes are what add up. Heavy metals take less volume per gram, so the correct method adds volumes per gram (w/ρ) and takes the reciprocal.

Why is Wood's metal used in fire sprinklers?

It melts at about 70 °C. In a fire, the plug melts, opens the valve and lets water spray out automatically.

Are compositions of these alloys fixed?

No. Commercial grades vary over a range, and different textbooks quote slightly different typical values. In the exam use the commonly quoted values given here or the values printed in the question.

These notes follow the University of Mumbai first-year engineering syllabus (NEP 2020, Engineering Materials) and were prepared with AI help and checked.

More in Engineering Materials

See all →