Wave Interference Notes FE Sem 2 Measurements and Sensors | MU
On this page
A light wave is a ruler with divisions about half a micrometre apart, and interference lets us read that ruler. This module of Physics of Measurements and Sensors (BSC2023, FE Semester 2) uses the interference of light in a thin air film to measure flatness and small height differences to a fraction of a micrometre, far beyond what a micrometer screw can do. You will learn why the light must be monochromatic, how an optical flat placed on a surface produces fringes, how to read straight, curved and irregular fringe patterns as a contour map of the surface, and how to turn a fringe count into a height. It maps to CO2 (execute the flatness test using light waves) and is a favourite source of short numericals.
Summary
Interference basics: When two light waves from the same source meet, their displacements add. If they arrive in phase (path difference a whole number of wavelengths) they reinforce and give a bright band; if they arrive half a wavelength out of step they cancel and give a dark band. To see a steady pattern the two waves must be coherent: they must keep a constant phase relation, which in practice means they come from the same source by division of amplitude (partial reflection at two surfaces of a thin film) or division of wavefront.
Significance of monochromatic light: Monochromatic light has a single wavelength (in practice a very narrow band). This matters for measurement in three ways. First, the fringe spacing depends on the wavelength; with one known wavelength every fringe corresponds to a known change of film thickness (λ/2 for an air film viewed normally), so counting fringes converts directly into height. Second, with white light each colour forms its own fringe system with different spacing; after the first few fringes the colours overlap and the pattern washes out into uniform white, so only a few coloured fringes are seen and they cannot be counted reliably. Third, monochromatic light has a longer coherence length, so fringes remain sharp and high in contrast even when the air gap is many wavelengths thick. Common sources in metrology are the sodium lamp (yellow, about 589.3 nm), the mercury lamp with a green filter (546.1 nm), the helium discharge lamp (587.6 nm) and the helium-neon laser (632.8 nm). Thallium (535 nm) and cadmium lamps have also been used.
The optical flat: An optical flat is a disc of fused quartz or optical glass, typically 25 to 300 mm in diameter and 12 to 25 mm thick, with one or both faces polished flat to within about 0.05 to 0.1 μm. When it is placed on a reasonably flat, reflective test surface (such as a slip gauge face or a lapped seal), it rests at a slight angle, enclosing a thin wedge of air. Light reflected from the bottom face of the flat and from the test surface interfere.
Air wedge fringes: For an air film of thickness t viewed at normal incidence, the path difference between the two reflected rays is 2t, and the ray reflected from the denser test surface suffers an extra phase change of π (equivalent to λ/2). Hence a dark fringe occurs where \(2t = n\lambda\) and a bright fringe where \(2t = (n + \tfrac{1}{2})\lambda\). Moving from one dark fringe to the next, the air gap changes by exactly λ/2. So each fringe is a contour line joining points of equal air gap, and adjacent fringes are contours λ/2 apart in height, about 0.29 μm for sodium or helium light. For a wedge of angle θ the fringe spacing is \(\beta = \lambda/(2\theta)\): a smaller angle gives wider, fewer fringes.
Interferometry applied to flatness testing: Place the optical flat on the clean test surface, illuminate with a monochromatic source (often a diffused lamp in a fixture so that light falls almost normally), and look down at the fringes. Straight, parallel, equally spaced fringes mean the surface is flat: the air wedge is a true plane wedge. Curved fringes mean the surface is not flat. To decide whether it is convex or concave, note where the flat touches (the contact edge, which can be found by gently pressing the flat and seeing where the fringes stay fixed). With the flat resting along one edge, a convex surface gives fringes whose middle bows away from the contact edge, and a concave surface gives fringes whose middle bows towards the contact edge, because a fringe follows a line of constant air gap and the gap is smaller where the surface is higher. Concentric circular fringes (like Newton's rings) indicate a spherical high spot or hollow; the number of rings gives its height in units of λ/2. Irregular fringe patterns map local hills and valleys. The amount of out-of-flatness is found from the curvature of the fringes: if the bow (departure of a fringe from a straight line drawn tangent to its ends) is a and the fringe spacing is b, the error of flatness is \((a/b)\times(\lambda/2)\).
Surface contour test: Because each fringe is a contour of equal air gap, the fringe pattern is literally a contour map of the surface relative to the reference plane of the flat. Straight equidistant lines mean a plane surface tilted slightly; closed loops mean a peak or depression; fringes that are closer together show steeper slope; a fringe that bends sharply near an edge shows a rolled-off (rounded) edge, which is common on lapped parts. Counting the number of fringes crossed between two points gives their height difference in multiples of λ/2. This contour reading is used to inspect lapped faces of slip gauges, micrometer anvils, pump and valve seals, mirrors and silicon wafers.
Comparing slip gauges (measurement of small height differences): A known master gauge and the gauge under test are wrung side by side on a flat base, a distance L apart. An optical flat laid across both forms air wedges over them. If the test gauge is higher or lower than the master by h, the flat is tilted by θ = h/L. Over the width w of the gauge face the gap changes by θw, which shows up as n fringes, so \(n\lambda/2 = hw/L\), or \(h = n\lambda L/(2w)\). Pressing on the flat over each gauge shows which one is higher. For higher accuracy, the NPL flatness interferometer uses a collimated monochromatic beam and a fixed reference flat set above the test surface, so that the pattern is not disturbed by contact.
Mind map
Measurements by Light: Wave Interference
- Interference
- Coherent sources, division of amplitude
- Bright: path difference nλ
- Dark: path difference (n + ½)λ
- Monochromatic light
- Known single wavelength
- Many sharp countable fringes
- Sodium, mercury green, helium, He-Ne laser
- Optical flat
- Fused quartz or glass, flat to 0.05 to 0.1 μm
- Forms an air wedge on test surface
- Each fringe = λ/2 change in gap
- Flatness testing
- Straight equal fringes: flat
- Curved fringes: convex or concave
- Error = (a/b)(λ/2)
- Surface contour
- Fringes are contour lines
- Closed rings: hill or hollow
- Crowded fringes: steep slope
- Gauge comparison
- h = nλL/(2w)
- NPL flatness interferometer
Why an air wedge gives fringes λ/2 apart
- An optical flat rests on the test surface at a tiny angle θ, enclosing an air film whose thickness t increases with distance x from the line of contact: \(t = x\tan\theta \approx x\theta\).
- Monochromatic light falls nearly normally. Part is reflected at the lower face of the flat (glass to air, no phase change) and part at the test surface (air to metal or glass, phase change π).
- Geometrical path difference between the two rays is 2t (the second ray crosses the film twice). Effective path difference \(= 2t + \lambda/2\).
- Dark fringe when the effective path difference is an odd multiple of λ/2, which simplifies to \(2t = n\lambda\), n = 0, 1, 2, ...; at the contact line t = 0, so it is dark.
- For the next dark fringe, \(2t' = (n+1)\lambda\), so \(t' - t = \lambda/2\): adjacent fringes differ in air gap by half a wavelength.
- Spacing on the surface: \(x_{n+1} - x_n = (\lambda/2)/\theta\), so \(\beta = \lambda/(2\theta)\).
- If the test surface is not plane, t varies irregularly and fringes follow the lines of equal t; they bend, and the bend in units of fringe spacing gives the height error in units of λ/2.
Reading fringe patterns
| Fringe pattern seen | What the surface is like |
|---|---|
| Straight, parallel, equally spaced | Flat surface; the flat is slightly tilted |
| Very few broad straight fringes | Flat surface with very small wedge angle |
| Fringes curved, bowing away from the contact edge | Convex surface (centre higher) |
| Fringes curved, bowing towards the contact edge | Concave surface (centre lower) |
| Concentric circles | Spherical hill (flat touches at the centre) or hollow (flat touches at the rim); decide by pressing (see below) |
| Fringes bending sharply near the edge | Rolled or rounded edge |
| Irregular, wavy fringes | Uneven surface with local high and low spots |
Rule for concentric rings: press gently at the centre of the flat. If the surface is a hollow (concave, the flat touches only at the rim), pressing at the centre reduces the air gap there, so the rings shrink towards the centre and some disappear. If the surface is a hill (convex, the flat already touches at the centre), pressing at the centre changes almost nothing. Books phrase this rule in different ways, so in the exam explain the reasoning: a fringe is a line of constant air gap, so when the gap is squeezed each fringe slides towards the region where the gap is still larger.
Important definitions
| Term | Meaning |
|---|---|
| Interference | Redistribution of light energy when two coherent waves superpose, giving bright and dark fringes. |
| Coherent sources | Sources that emit waves of the same frequency with a constant phase difference. |
| Monochromatic light | Light of a single wavelength or a very narrow band of wavelengths. |
| Coherence length | The path difference over which a source's light remains coherent; longer for more monochromatic sources. |
| Optical flat | A transparent disc of quartz or glass with a highly flat polished face used as a reference plane in interference tests. |
| Air wedge | Thin wedge-shaped air film between two surfaces inclined at a small angle. |
| Fringe | Bright or dark band joining points of equal path difference (equal air gap). |
| Fringe width | Distance between two successive bright or dark fringes, \(\beta = \lambda/2\theta\) for an air wedge. |
| Flatness | The condition of a surface in which all points lie between two parallel planes a specified small distance apart. |
| Surface contour | The shape of the surface shown as lines of equal height; interference fringes are such lines. |
Formulas
| Formula | Meaning |
|---|---|
| \( 2t = n\lambda \) | Dark fringe condition for an air film at normal incidence (reflected light). |
| \( 2t = \left(n + \tfrac{1}{2}\right)\lambda \) | Bright fringe condition. |
| \( \Delta t = \dfrac{\lambda}{2} \) | Change in air gap between adjacent fringes. |
| \( h = n\,\dfrac{\lambda}{2} \) | Height difference across n fringes. |
| \( \beta = \dfrac{\lambda}{2\theta} \) | Fringe spacing for a wedge of angle θ (radian). |
| \( e = \dfrac{a}{b}\cdot\dfrac{\lambda}{2} \) | Flatness error from fringe bow a and fringe spacing b. |
| \( h = \dfrac{n\lambda L}{2w} \) | Height difference of two slip gauges a distance L apart, n fringes across gauge width w. |
Key points to remember
- Use monochromatic light: known λ, sharp and countable fringes; white light gives only a few coloured fringes.
- Each fringe of an air wedge corresponds to λ/2 change in gap, about 0.29 μm for helium (587.6 nm) or sodium light.
- Fringes are contour lines of equal air gap: the pattern is a contour map of the surface.
- Straight, parallel, equidistant fringes indicate a flat surface.
- Curved fringes indicate convex or concave surfaces; decide by pressing the flat.
- Flatness error = (bow ÷ spacing) × λ/2.
- The contact line of an air wedge in reflected light is dark (extra λ/2 phase change).
- Surfaces must be clean, reflective and reasonably smooth (lapped or polished) and at the same temperature as the flat.
- Optical flats should never be slid on a surface: dust scratches them; lift and place gently.
Solved examples
Example 1. An optical flat is placed on a lapped surface and viewed with sodium light (λ = 589.3 nm). Six fringes are counted between the point of contact and the far edge. What is the height difference across the surface?
Each fringe = λ/2 = 294.65 nm. \(h = 6\times294.65 = 1768\) nm \(\approx 1.77\) μm.
Example 2. Fringes on a surface tested with helium light (587.6 nm) are curved. The bow of a fringe is 0.3 of the fringe spacing. Find the flatness error.
\(e = (a/b)(\lambda/2) = 0.3\times587.6/2 = 0.3\times293.8 = 88.1\) nm \(\approx 0.09\) μm. The surface is out of flat by about 0.09 μm across the width examined.
Example 3. An air wedge is formed at an angle of 0.01°. Find the fringe spacing for λ = 589.3 nm. What angle gives a spacing of 1 mm?
θ = 0.01° = \(1.745\times10^{-4}\) rad. \(\beta = \lambda/(2\theta) = 589.3\times10^{-9}/(3.491\times10^{-4}) = 1.69\times10^{-3}\) m = 1.69 mm. For β = 1 mm, \(\theta = \lambda/(2\beta) = 589.3\times10^{-9}/(2\times10^{-3}) = 2.95\times10^{-4}\) rad (about 0.017°).
Example 4. A slip gauge under test and a master gauge are wrung on a flat base 40 mm apart. An optical flat across them shows 8 fringes across the 20 mm width of the test gauge in sodium light (589.3 nm). Find the difference in their heights.
\(h = n\lambda L/(2w) = 8\times589.3\times10^{-9}\times40/(2\times20) = 4.71\times10^{-6}\) m = 4.71 μm. Pressing over each gauge tells which is higher.
Example 5. A surface examined with mercury green light (546.1 nm) shows 10 concentric rings. Estimate the height of the hill or depth of the hollow.
\(h = 10\times546.1/2 = 2730\) nm \(\approx 2.73\) μm.
Important questions and answers
Q1. Explain the significance of monochromatic light in interference measurements. (5 marks)
Interference fringes are formed where the path difference is a definite multiple of the wavelength. With monochromatic light: (1) there is only one known wavelength, so each fringe represents a definite change in thickness, λ/2 for an air film, and counting fringes gives height directly; (2) the light has a long coherence length, so interference persists for larger air gaps and many sharp, high contrast fringes appear; (3) the fringe spacing is uniform for a uniform wedge, making shape errors easy to see. White light contains many wavelengths, each producing its own fringe pattern with different spacing; except for the first one or two coloured fringes near contact the patterns overlap and give uniform illumination, so no measurement is possible. Typical sources: sodium (589.3 nm), helium (587.6 nm), mercury green (546.1 nm), He-Ne laser (632.8 nm).
Q2. With a neat diagram explain how an optical flat is used to test the flatness of a surface. (6 marks)
Diagram: monochromatic source with diffuser above, optical flat resting on the test surface touching at one edge, thin air wedge, eye looking down. Working: light reflects from the lower face of the flat and from the test surface; the two reflected rays interfere. Dark fringes occur where \(2t = n\lambda\), so successive dark fringes mark air gaps differing by λ/2, forming a contour map. Interpretation: straight, parallel and equally spaced fringes show the surface is flat; curved fringes show convexity or concavity (press the flat to tell which); concentric rings show a spherical high or low spot; irregular fringes show uneven surface. Quantity: error of flatness \(= (a/b)(\lambda/2)\), where a is the bow of a fringe and b the fringe spacing, or n × λ/2 for n rings or fringes. Precautions: clean surfaces, temperature equalisation, light normal to the surface, flat placed without sliding.
Q3. Derive the expression for fringe width in an air wedge and show that adjacent fringes differ in thickness by λ/2. (5 marks)
Let the wedge angle be θ and thickness at distance x be \(t = x\theta\). For normal incidence, the effective path difference between rays reflected from top and bottom of the air film is \(2t + \lambda/2\), because reflection from the denser lower surface introduces a phase change of π. For the n-th dark fringe, \(2t_n + \lambda/2 = (2n+1)\lambda/2\), giving \(2t_n = n\lambda\). For the (n+1)-th dark fringe, \(2t_{n+1} = (n+1)\lambda\). Subtracting, \(t_{n+1} - t_n = \lambda/2\). Since \(t = x\theta\), \(x_{n+1} - x_n = \lambda/(2\theta)\), so the fringe width \(\beta = \lambda/(2\theta)\), which is uniform for a plane wedge.
Q4. What is meant by a surface contour test using interference? How are different fringe patterns interpreted? (5 marks)
The fringes produced between an optical flat and a surface join points of equal air gap, so they are contour lines of the surface with a contour interval of λ/2, like contour lines on a map with a vertical spacing of about 0.3 μm. Surface contour testing means reading this map: parallel straight lines show a plane surface; curved lines show a cylindrical or spherical form error; closed loops show isolated peaks or pits; closely crowded fringes show steep slope; fringes turning at an edge show edge roll-off; zig-zag fringes show scratches or steps. The number of fringes between two points gives their height difference, n × λ/2. Used for lapped gauge faces, seal faces, mirrors, lenses and wafers.
Q5. Two slip gauges are compared using an optical flat. Explain the method and give the formula for the height difference. (5 marks)
The master gauge and the gauge under test are wrung on an optically flat base plate a distance L apart, and an optical flat is placed across them. If the gauges differ in height by h, the flat makes an angle θ = h/L with the gauge faces, forming air wedges over both. Under monochromatic light, n fringes are counted across the width w of a gauge face. The air gap changes by θw over this width, which equals nλ/2, so \(h = n\lambda L/(2w)\). If both faces show the same number of fringes the faces are parallel; a different number or curvature indicates lack of parallelism or flatness. Pressing on the flat over one gauge shows which is higher.
Q6. Why is the point of contact of an air wedge dark in reflected light? (3 marks)
At the contact line the air film thickness is zero, so the geometrical path difference is zero. But the ray reflected from the lower surface (air to denser medium) suffers a phase change of π, equal to a path of λ/2. The two rays are therefore half a wavelength out of step and cancel, so the contact line appears dark.
Exam tips
- Draw the optical flat set-up with source, diffuser, flat, air wedge and observer; label the angle θ.
- Always state "each fringe represents λ/2" before any calculation.
- Convert nanometres to micrometres in the final answer; flatness errors are usually fractions of a micrometre to a few micrometres.
- Sketch the four classic patterns: straight, curved convex, curved concave, concentric rings.
- In the monochromatic light question, contrast with white light for full marks.
- For gauge comparison remember the ratio L/w; students often forget it.
FAQs
Why not use a laser for every flatness test?
A He-Ne laser is very monochromatic and is used in laser interferometers. For simple optical flat checks a diffused lamp is easier on the eye and gives a wider, even field of view, so discharge lamps are common in workshops.
How accurate is the optical flat method?
Errors of a fraction of a fringe, around 0.05 to 0.1 μm, can be judged by eye. The limit is set by the flatness of the optical flat itself and by the skill of the observer.
Can rough surfaces be tested with an optical flat?
No. The surface must reflect light well and be smooth, such as a lapped, ground or polished surface. Rough machined surfaces scatter light and no clear fringes form.
Which sources are used and why?
Sodium, helium, mercury (green line) and He-Ne lasers, because each gives a strong, nearly single wavelength that is known accurately.
These notes follow the University of Mumbai first-year engineering syllabus (NEP 2020, Physics of Measurements and Sensors) and were prepared with AI help and checked.
More in Physics of Measurements and Sensors
See all →- Nanotechnology Notes FE Sem 2 Measurements and Sensors | MU MU FE Sem 2 Measurements and Sensors Module 6: nano properties, surface to volume ratio, van der Waals bonding, SEM, TEM, AFM, gas sensing,...
- Measurement Errors Notes FE Sem 2 Measurements and Sensors | MU MU FE Sem 2 Measurements and Sensors Module 1: errors, calibration, instrument terms, accuracy, precision, standard deviation, least squares...
- Transducers Notes FE Sem 2 Measurements and Sensors | MU MU FE Sem 2 Physics of Measurements and Sensors Module 3: transducer classification, potentiometer, strain gauge, RTD, LVDT and thermal phot...
- Solid State Sensors Notes FE Sem 2 Measurements and Sensors | MU MU FE Sem 2 Measurements and Sensors Module 4: Hall effect and Hall voltage, piezoelectric ultrasonics, ultrasonic flow and distance meters.
- Temperature Notes FE Sem 2 Measurements and Sensors | MU MU FE Sem 2 Measurements and Sensors Module 5: bimetallic, Pt-100, thermocouple and NTC thermistor thermometers, selection, Pt-100 calibrati...