Skip to content
doubtly

Air Pollution Notes FE Sem 2 Environmental Chemistry | MU

Doubtly 17 min read Updated 27 Oct 2026 Save WhatsApp Save as PDF
On this page

Every winter the air quality index of Indian cities makes headlines, and behind those numbers is chemistry: sulphur and nitrogen oxides turning into acids, chlorine atoms eating ozone, and sunlight cooking exhaust gases into smog. This first module of Environmental Chemistry and Non-conventional Energy Sources (BSC2032, FE Semester 2, NEP 2020) explains the reactions behind three global effects of air pollution (acid rain, the ozone hole and photochemical smog), how the main gaseous pollutants are measured, how emissions of sulphur oxides, nitrogen oxides, carbon monoxide and hydrocarbons are controlled, and how vehicle emissions are measured and reduced with catalytic converters. It maps to CO1. Reaction-based explanations with balanced equations score the most marks here.

Summary

Air pollution and the atmosphere: Air pollution is the presence in the atmosphere of substances in concentrations that harm people, animals, plants or materials. Primary pollutants are emitted directly (SO2, NO, CO, hydrocarbons, particulates); secondary pollutants form in the air by reactions among primary pollutants and natural components (H2SO4 and HNO3 in acid rain, ozone and PAN in smog). The lowest layer, the troposphere (up to about 10 to 16 km), contains most of the air and weather; above it the stratosphere (up to about 50 km) contains the ozone layer, with the highest ozone concentration around 20 to 30 km.

Acid rain: Pure rain water in equilibrium with atmospheric CO2 is naturally slightly acidic, pH about 5.6, because of carbonic acid. Rain with pH below 5.6 is called acid rain; values of 4 to 4.5 have been recorded in industrial regions. The main culprits are SO2 (from burning coal and oil, smelting of sulphide ores) and NOx (from vehicles and power plants, where N2 and O2 combine at high flame temperature). In the air they are oxidised and dissolved:

\[ 2SO_2 + O_2 \rightarrow 2SO_3, \qquad SO_3 + H_2O \rightarrow H_2SO_4 \]

\[ 2NO + O_2 \rightarrow 2NO_2, \qquad 4NO_2 + O_2 + 2H_2O \rightarrow 4HNO_3 \]

The gas phase oxidation is mainly driven by the hydroxyl radical (\(SO_2 + OH\cdot \rightarrow HSO_3\cdot\), \(NO_2 + OH\cdot \rightarrow HNO_3\)), and in cloud droplets SO2 is oxidised by H2O2 and O3. About 60 to 70 percent of the acidity is usually due to sulphuric acid and 30 to 40 percent to nitric acid. Acids reach the ground as wet deposition (rain, snow, fog) or dry deposition (gases and particles). Effects: lakes and streams become acidic and fish die; acid leaches Al³⁺ from soils, which is toxic to fish and trees, and washes away nutrients such as Ca²⁺ and Mg²⁺; forests are damaged; buildings and monuments of marble and limestone corrode, \(CaCO_3 + H_2SO_4 \rightarrow CaSO_4 + H_2O + CO_2\) (the yellowing and pitting of the Taj Mahal, called stone leprosy, has been linked to the Mathura refinery and other sources); metals corrode; human respiratory problems increase. Control: reduce SO2 and NOx emissions (see below); liming of acidified lakes treats the symptom.

Ozone hole: In the stratosphere ozone is formed and destroyed naturally (Chapman cycle). UV radiation below about 242 nm splits oxygen; the atoms combine with O2 to form ozone, which absorbs harmful UV-B and UV-C and is split again:

\[ O_2 \xrightarrow{h\nu} 2O, \quad O + O_2 + M \rightarrow O_3 + M, \quad O_3 \xrightarrow{h\nu} O_2 + O, \quad O + O_3 \rightarrow 2O_2 \]

where M is a third body (N2 or O2) that carries away energy. This steady state shields life from UV. Chlorofluorocarbons (CFCs, such as CFC-11 CFCl3 and CFC-12 CF2Cl2, used as refrigerants, aerosol propellants and foaming agents) are very stable and reach the stratosphere, where UV breaks them and releases chlorine atoms, which destroy ozone catalytically:

\[ CF_2Cl_2 \xrightarrow{h\nu} CF_2Cl\cdot + Cl\cdot, \quad Cl\cdot + O_3 \rightarrow ClO\cdot + O_2, \quad ClO\cdot + O \rightarrow Cl\cdot + O_2 \]

The net reaction is \(O_3 + O \rightarrow 2O_2\); the chlorine atom is regenerated, so one Cl atom can destroy tens of thousands of ozone molecules before it is locked up. Bromine from halons and methyl bromide acts the same way and is even more destructive per atom; NO from high flying aircraft also catalyses ozone loss. The Antarctic ozone hole appears every spring (September to November): during the dark polar winter polar stratospheric clouds form at about −80 °C, and on their ice surfaces the inactive reservoirs HCl and ClONO2 are converted into Cl2 (\(ClONO_2 + HCl \rightarrow Cl_2 + HNO_3\)); when sunlight returns in spring, Cl2 is split into Cl atoms which rapidly destroy ozone. Ozone is measured in Dobson units (1 DU = 0.01 mm thickness of pure ozone at STP); the global average is about 300 DU and the hole is the region below 220 DU. Effects: more UV-B causes skin cancer, cataracts, weakened immunity, damage to crops and phytoplankton. Control: the Montreal Protocol (1987) phased out CFCs, halons and other ozone depleting substances; HCFCs are being phased out and the Kigali Amendment (2016) phases down HFCs because they are strong greenhouse gases. The ozone layer is recovering and is expected to return to 1980 levels around the middle of this century.

Photochemical smog: Photochemical (Los Angeles type) smog is a brownish, oxidising haze formed on sunny days in cities with heavy traffic, when NOx and volatile organic compounds (VOCs, hydrocarbons) react in sunlight. It differs from classical (London type) smog, which is a reducing mixture of smoke, fog and SO2 formed in cold damp weather. Mechanism: NO2 absorbs sunlight (below about 400 nm) and splits; the oxygen atom forms ozone; normally ozone reacts back with NO:

\[ NO_2 \xrightarrow{h\nu} NO + O, \quad O + O_2 + M \rightarrow O_3 + M, \quad O_3 + NO \rightarrow NO_2 + O_2 \]

This cycle alone would not accumulate ozone. Hydrocarbons break it: they are attacked by OH radicals to form peroxy radicals (RO2·), which convert NO to NO2 without using up ozone (\(RO_2\cdot + NO \rightarrow RO\cdot + NO_2\)), so ozone builds up. Further reactions produce aldehydes (formaldehyde, acrolein) and peroxyacetyl nitrate (PAN): \(CH_3C(O)OO\cdot + NO_2 \rightarrow CH_3C(O)OONO_2\). The main smog products (O3, PAN, aldehydes, NO2) are secondary pollutants. A typical day shows NO peaking during morning traffic, then NO2, then ozone peaking in the early afternoon. Effects: eye, nose and throat irritation, asthma, reduced visibility, cracking of rubber, damage to crops and plants. Control: reduce NOx and VOC emissions from vehicles (catalytic converters, cleaner fuels), vapour recovery, public transport.

Measurement of gaseous pollutants: Sampling uses gas bubblers or impingers containing an absorbing solution through which a measured volume of air is drawn (for wet chemical methods), or continuous analysers. Sulphur dioxide: the West-Gaeke (modified, pararosaniline) method, in which SO2 is absorbed in sodium tetrachloromercurate to form a stable complex that reacts with formaldehyde and pararosaniline to give a coloured product measured by spectrophotometer at about 560 nm; continuous monitors use UV fluorescence. Nitrogen dioxide: the modified Jacob and Hochheiser method (absorption in sodium hydroxide with sodium arsenite, then diazotisation with sulphanilamide and coupling with NEDA to give an azo dye measured at about 540 nm); continuous monitors use chemiluminescence, \(NO + O_3 \rightarrow NO_2^* + O_2\), \(NO_2^* \rightarrow NO_2 + h\nu\), where the light emitted is proportional to NO (NO2 is first converted to NO). Carbon monoxide: non-dispersive infrared (NDIR) analysers, since CO absorbs IR at about 4.6 μm. Hydrocarbons: flame ionisation detector (FID), often after gas chromatography to separate methane and non-methane hydrocarbons. Ozone: UV photometry (absorption at 254 nm). Concentrations are reported in ppm or μg/m³ and compared with the National Ambient Air Quality Standards (NAAQS, 2009); for example the 24-hour limit is 80 μg/m³ for both SO2 and NO2 and the 8-hour limit for CO is 2 mg/m³.

Control of sulphur oxides: Use low-sulphur fuels and switch to natural gas; desulphurise fuels (hydrodesulphurisation of petroleum, washing of coal to remove pyrite); fluidised bed combustion in which limestone is added with coal and captures SO2 in the bed; flue gas desulphurisation (FGD): wet limestone scrubbing, \(CaCO_3 + SO_2 \rightarrow CaSO_3 + CO_2\), \(2CaSO_3 + O_2 \rightarrow 2CaSO_4\) (gypsum, usable in cement and plaster), or lime scrubbing and dry sorbent injection; tall stacks only disperse (not reduce) SO2.

Control of nitrogen oxides: Combustion modification: lower flame temperature and less excess air (low-NOx burners, staged combustion, flue gas recirculation, water or steam injection), because thermal NOx forms rapidly above about 1500 °C. Flue gas treatment: selective catalytic reduction (SCR) with ammonia over V2O5/TiO2 catalyst at about 300 to 400 °C, \(4NO + 4NH_3 + O_2 \rightarrow 4N_2 + 6H_2O\); selective non-catalytic reduction (SNCR) with ammonia or urea at about 900 to 1100 °C; absorption in alkaline solutions.

Control of carbon monoxide: CO comes from incomplete combustion. Control by proper air-fuel ratio, good mixing and sufficient temperature and time for complete combustion; catalytic oxidation (\(2CO + O_2 \rightarrow 2CO_2\) on Pt or Pd) in vehicles; afterburners in industry; tuning of engines and burners.

Control of gaseous hydrocarbons: Reduce evaporation (vapour recovery systems at petrol pumps, floating roof tanks, sealed fuel systems), adsorption on activated carbon (with recovery of solvent), absorption in suitable liquids, condensation, thermal incineration or flaring (to CO2 and H2O) and catalytic oxidation at lower temperatures, and biofilters for odorous VOCs.

Automotive emission measurement and control: Petrol and diesel engines emit CO, unburnt hydrocarbons, NOx and particulate matter (mainly diesel), along with CO2. Measurement: exhaust gas analysers use NDIR for CO, CO2 and HC and electrochemical or chemiluminescence sensors for NOx and O2; diesel smoke is measured by opacity meters; in India periodic Pollution Under Control (PUC) checks are required, and new vehicles are type-approved on standard driving cycles. India moved directly from Bharat Stage IV to Bharat Stage VI norms from 1 April 2020. Control methods: improved engine design and electronic fuel injection; exhaust gas recirculation (EGR) to lower flame temperature and NOx; positive crankcase ventilation (PCV) to burn blow-by gases; evaporative emission control with a charcoal canister; and exhaust after-treatment.

Catalytic converters: A three-way catalytic converter (TWC) in petrol vehicles is a stainless steel shell containing a ceramic (cordierite) or metal honeycomb with many fine channels, coated with a porous alumina washcoat on which small amounts of platinum, palladium and rhodium are dispersed. It removes all three pollutants at once: oxidation of CO and HC (Pt, Pd) and reduction of NOx (Rh):

\[ 2CO + O_2 \rightarrow 2CO_2, \quad C_xH_y + \left(x + \tfrac{y}{4}\right)O_2 \rightarrow xCO_2 + \tfrac{y}{2}H_2O, \quad 2NO + 2CO \rightarrow N_2 + 2CO_2 \]

It works efficiently (above 90 percent) only near the stoichiometric air-fuel ratio of about 14.7:1, which is maintained by an oxygen (lambda) sensor feeding the engine control unit, and only after warming up to about 250 to 300 °C. Lead and sulphur poison the catalyst, which is why unleaded, low-sulphur petrol is mandatory. Diesel vehicles, which run lean, use a diesel oxidation catalyst (DOC), a diesel particulate filter (DPF) and SCR with urea solution (diesel exhaust fluid): \((NH_2)_2CO + H_2O \rightarrow 2NH_3 + CO_2\), then ammonia reduces NOx to N2.

Mind map

Air Pollution and Atmospheric Chemistry

  • Acid rain
    • pH below 5.6
    • SO2 to H2SO4, NOx to HNO3
    • Lakes, forests, marble, metals
  • Ozone hole
    • Chapman cycle
    • CFC releases Cl, Cl + O3 chain
    • Polar stratospheric clouds
    • Montreal Protocol 1987
  • Photochemical smog
    • NO2 + sunlight gives O
    • O3, PAN, aldehydes
    • Hydrocarbons convert NO to NO2
  • Measurement
    • SO2: West-Gaeke, UV fluorescence
    • NO2: Jacob-Hochheiser, chemiluminescence
    • CO: NDIR, HC: FID
  • Control
    • SOx: low S fuel, FGD limestone
    • NOx: low NOx burners, SCR, SNCR
    • CO: complete combustion, oxidation catalyst
    • HC: vapour recovery, adsorption, incineration
  • Vehicles
    • Exhaust analysers, PUC, BS VI
    • EGR, PCV, canister
    • Three-way converter Pt, Pd, Rh

Chain reaction of ozone destruction step by step

  1. CFCs are inert in the lower atmosphere, so they survive for decades and slowly diffuse up into the stratosphere.
  2. Above the ozone maximum, short-wave UV breaks a C-Cl bond: \(CFCl_3 \xrightarrow{h\nu} CFCl_2\cdot + Cl\cdot\).
  3. The chlorine atom attacks ozone: \(Cl\cdot + O_3 \rightarrow ClO\cdot + O_2\).
  4. Chlorine monoxide meets an oxygen atom: \(ClO\cdot + O \rightarrow Cl\cdot + O_2\), regenerating Cl.
  5. Net: \(O_3 + O \rightarrow 2O_2\); Cl acts as a catalyst and repeats the cycle many thousands of times.
  6. Chain stops when Cl is stored as HCl (\(Cl + CH_4 \rightarrow HCl + CH_3\)) or ClONO2 (\(ClO + NO_2 \rightarrow ClONO_2\)).
  7. Over Antarctica, polar stratospheric cloud surfaces convert these reservoirs into Cl2, which sunlight splits in spring, causing rapid ozone loss and the ozone hole.

Classical smog versus photochemical smog

PointClassical (London) smogPhotochemical (Los Angeles) smog
NatureReducingOxidising
Main pollutantsSmoke, soot, SO2, fog dropletsNOx, hydrocarbons, O3, PAN, aldehydes
WeatherCold, humid, foggy, early morningWarm, dry, sunny, midday
SourceCoal burningVehicle exhaust
EffectsBronchitis, lung diseaseEye irritation, asthma, crop and rubber damage

Important definitions

TermMeaning
Primary pollutantPollutant emitted directly from a source (SO2, NO, CO).
Secondary pollutantPollutant formed in the atmosphere by reactions of primary pollutants (O3, PAN, H2SO4).
Acid rainPrecipitation with pH below 5.6 due to dissolved sulphuric and nitric acids.
Dobson unitMeasure of total ozone column; 1 DU = 0.01 mm of pure ozone at STP.
Ozone holeRegion where total ozone falls below 220 DU, seen over Antarctica each spring.
CFCsChlorofluorocarbons; stable compounds of C, F and Cl that release Cl in the stratosphere.
Photochemical smogOxidising haze of O3, PAN, aldehydes and NO2 formed by sunlight acting on NOx and hydrocarbons.
PANPeroxyacetyl nitrate, CH3C(O)OONO2, an eye irritant in smog.
Flue gas desulphurisationRemoval of SO2 from exhaust gases, usually by limestone or lime scrubbing.
Selective catalytic reductionReduction of NOx to N2 using ammonia over a catalyst.
Three-way catalytic converterDevice that oxidises CO and HC and reduces NOx simultaneously on Pt, Pd and Rh.
EGRExhaust gas recirculation; returning part of the exhaust to the intake to lower flame temperature and NOx.

Formulas

FormulaMeaning
\( \mu g/m^3 = \dfrac{ppm \times M \times 1000}{24.45} \)Converting gas concentration at 25 °C and 1 atm (M = molar mass in g/mol).
\( mg/m^3 = \dfrac{ppm \times M}{24.45} \)Same, in mg/m³.
\( pH = -\log_{10}[H^+] \)Acidity of rain; natural rain about 5.6.
\( 2SO_2 + O_2 \rightarrow 2SO_3;\ SO_3 + H_2O \rightarrow H_2SO_4 \)Sulphuric acid in acid rain.
\( 4NO_2 + O_2 + 2H_2O \rightarrow 4HNO_3 \)Nitric acid in acid rain.
\( Cl + O_3 \rightarrow ClO + O_2;\ ClO + O \rightarrow Cl + O_2 \)Catalytic destruction of ozone.
\( NO_2 \xrightarrow{h\nu} NO + O;\ O + O_2 \rightarrow O_3 \)Ozone formation in smog.
\( CaCO_3 + SO_2 \rightarrow CaSO_3 + CO_2 \)Limestone scrubbing of SO2.
\( 4NO + 4NH_3 + O_2 \rightarrow 4N_2 + 6H_2O \)SCR of NOx.
\( 2NO + 2CO \rightarrow N_2 + 2CO_2 \)NOx reduction in a three-way converter.

Key points to remember

  • Natural rain pH is about 5.6 (CO2); acid rain is below 5.6.
  • H2SO4 contributes most of the acidity, HNO3 the rest.
  • Ozone layer is in the stratosphere (about 20 to 30 km); ozone at ground level is a pollutant.
  • One chlorine atom destroys thousands of ozone molecules because it is regenerated.
  • Antarctic ozone hole forms in spring because of polar stratospheric clouds and returning sunlight.
  • Photochemical smog needs sunlight, NOx and hydrocarbons; it is oxidising.
  • SO2: West-Gaeke; NO2: Jacob-Hochheiser or chemiluminescence; CO: NDIR; HC: FID.
  • FGD by limestone produces gypsum; SCR uses ammonia to turn NOx into N2.
  • Three-way converter: Pt and Pd oxidise CO and HC, Rh reduces NOx; needs air-fuel ratio about 14.7:1 and unleaded fuel.
  • India adopted Bharat Stage VI from 1 April 2020.

Solved examples

Example 1. The SO2 concentration in a city is 0.1 ppm. Express it in μg/m³ at 25 °C and 1 atm (S = 32.06, O = 16.00).

M(SO2) = 64.06 g/mol. \(C = 0.1\times64.06\times1000/24.45 = 262\) μg/m³. This is far above the 24-hour NAAQS limit of 80 μg/m³.

Example 2. CO in a busy street is 9 ppm. Convert to mg/m³.

M(CO) = 28.01. \(C = 9\times28.01/24.45 = 10.3\) mg/m³.

Example 3. Express 80 μg/m³ of NO2 in ppb (M = 46.01, 25 °C).

\(ppm = 80\times24.45/(46.01\times1000) = 0.0425\) ppm = 42.5 ppb.

Example 4. A rain sample has [H⁺] = \(2.5\times10^{-5}\) mol/L. Find its pH. Is it acid rain?

\(pH = -\log(2.5\times10^{-5}) = 5 - 0.398 = 4.60\). Since 4.60 < 5.6, it is acid rain, about ten times more acidic than natural rain (\(10^{5.6-4.6} = 10\)).

Example 5. How much limestone (CaCO3) is theoretically needed to remove the SO2 produced by burning 1 tonne of coal containing 2 percent sulphur?

Sulphur = 20 kg. \(S + O_2 \rightarrow SO_2\) and \(CaCO_3 + SO_2 \rightarrow CaSO_3 + CO_2\): 32 kg S needs 100 kg CaCO3. So CaCO3 = 20 × 100/32 = 62.5 kg (in practice some excess is used).

Important questions and answers

Q1. Explain the chemistry of acid rain and its effects. (5 marks)

Formation: SO2 and NOx from fuel combustion are oxidised in air (by O2, OH radicals, O3 and H2O2) and dissolved in water: \(2SO_2 + O_2 \rightarrow 2SO_3\), \(SO_3 + H_2O \rightarrow H_2SO_4\); \(2NO + O_2 \rightarrow 2NO_2\), \(4NO_2 + O_2 + 2H_2O \rightarrow 4HNO_3\). Rain with pH below 5.6 results. Effects: acidification of lakes and death of fish; leaching of soil nutrients and release of toxic aluminium; damage to forests and crops; corrosion of metals and decay of marble buildings (\(CaCO_3 + H_2SO_4 \rightarrow CaSO_4 + CO_2 + H_2O\)); respiratory illness. Control: reduce SO2 and NOx at source, FGD, low NOx burners, catalytic converters; liming of lakes.

Q2. Explain the mechanism of ozone depletion. Why is it most severe over Antarctica? (6 marks)

Natural balance by Chapman reactions. CFCs reach the stratosphere and photolyse to release Cl atoms. Catalytic cycle: \(Cl + O_3 \rightarrow ClO + O_2\); \(ClO + O \rightarrow Cl + O_2\); net \(O_3 + O \rightarrow 2O_2\). Nitric oxide does the same: \(NO + O_3 \rightarrow NO_2 + O_2\), \(NO_2 + O \rightarrow NO + O_2\). Antarctica: very cold polar vortex in winter forms polar stratospheric clouds; on them HCl and ClONO2 react to form Cl2 and HNO3, and nitrogen is removed as nitric acid; in spring, sunlight splits Cl2 into Cl atoms and ozone is destroyed rapidly, giving the ozone hole (below 220 DU). Effects of UV-B: skin cancer, cataract, crop and plankton damage. Control: Montreal Protocol, substitutes, Kigali Amendment.

Q3. What is photochemical smog? Explain its formation with reactions and its effects. (6 marks)

An oxidising brown haze formed in sunny, traffic-heavy cities. Reactions: \(NO_2 \xrightarrow{h\nu} NO + O\); \(O + O_2 \rightarrow O_3\); \(O_3 + NO \rightarrow NO_2 + O_2\) (balance). Hydrocarbons + OH → RO2; \(RO_2 + NO \rightarrow RO + NO_2\), so NO is removed without consuming ozone and O3 accumulates. Further products: aldehydes (HCHO, acrolein) and PAN (\(CH_3C(O)OO + NO_2 \rightarrow CH_3C(O)OONO_2\)). Effects: eye irritation, breathing problems and asthma, reduced visibility, damage to plants (leaf injury), cracking of rubber and fading of dyes. Control: catalytic converters, reducing VOC evaporation, CNG and electric vehicles, public transport.

Q4. Explain methods to control emissions of SO2 and NOx from power plants. (6 marks)

SO2: low-sulphur coal or fuel switching; coal washing; fluidised bed combustion with limestone; wet limestone FGD scrubber (\(CaCO_3 + SO_2 \rightarrow CaSO_3 + CO_2\), oxidised to gypsum); spray dry lime scrubbers; dry sorbent injection. NOx: low-NOx burners and staged combustion to lower peak flame temperature and oxygen; flue gas recirculation; SCR with NH3 over V2O5/TiO2 (\(4NO + 4NH_3 + O_2 \rightarrow 4N_2 + 6H_2O\)); SNCR with urea at high temperature. Mention that FGD and SCR are being installed in Indian thermal power plants to meet emission norms.

Q5. Describe the construction and working of a three-way catalytic converter. (6 marks)

Construction: stainless steel housing in the exhaust line; inside, a ceramic (cordierite) honeycomb monolith with hundreds of channels per square inch, coated with an alumina washcoat (with ceria as oxygen storage) carrying Pt, Pd and Rh. An oxygen (lambda) sensor before the converter controls the air-fuel ratio at about 14.7:1. Working: as exhaust passes, CO and HC are oxidised to CO2 and H2O (Pt, Pd), and NO is reduced to N2 by CO, H2 or HC (Rh): \(2CO + O_2 \rightarrow 2CO_2\); \(C_xH_y + (x + y/4)O_2 \rightarrow xCO_2 + (y/2)H_2O\); \(2NO + 2CO \rightarrow N_2 + 2CO_2\). Conversion above 90 percent after light-off at about 250 to 300 °C. Precautions: unleaded low-sulphur fuel (lead and sulphur poison the catalyst), avoid misfiring which overheats it. Diesel engines use DOC, DPF and urea SCR instead.

Q6. How are SO2 and NO2 in ambient air measured? (5 marks)

SO2 by the improved West-Gaeke method: air bubbled through potassium or sodium tetrachloromercurate forms dichlorosulphitomercurate complex; formaldehyde and acid-bleached pararosaniline produce a red-purple pararosaniline methyl sulphonic acid measured at about 560 nm; concentration from a calibration curve; continuous analysers use UV fluorescence. NO2 by the modified Jacob-Hochheiser method: absorption in NaOH plus sodium arsenite to form nitrite; reaction with sulphanilamide and NEDA gives an azo dye measured at about 540 nm; continuous analysers use chemiluminescence of NO with ozone. Results are compared with NAAQS.

Exam tips

  • Write balanced equations for every mechanism; a mechanism without equations loses most marks.
  • Use the dot or radical sign for Cl, ClO and OH in ozone reactions.
  • Compare classical and photochemical smog in a table.
  • For catalytic converters name the three metals and their roles and mention the lambda sensor.
  • Learn one measurement method for each of SO2, NO2, CO and HC.
  • Use the 24.45 L/mol molar volume (25 °C) for ppm to μg/m³ conversions and state the condition.

FAQs

Is ozone good or bad?

Both. In the stratosphere it absorbs harmful UV and protects life. At ground level it is a toxic secondary pollutant in smog that harms lungs and crops.

Why is normal rain acidic?

Carbon dioxide dissolves in rain to form weak carbonic acid, giving a pH of about 5.6. Only rain below this pH is called acid rain.

Why can't leaded petrol be used with a catalytic converter?

Lead deposits on the precious metal sites and permanently poisons the catalyst, so the converter stops working.

Has the Montreal Protocol worked?

Yes. Atmospheric chlorine from ozone depleting substances is falling, and assessments expect the ozone layer to recover to 1980 levels over most of the world around the middle of the century, later over Antarctica.

These notes follow the University of Mumbai first-year engineering syllabus (NEP 2020, Environmental Chemistry and Non-conventional Energy Sources) and were prepared with AI help and checked.

More in Environmental Chemistry and Non-conventional energy sources

See all →