Engineering Mechanics
- How do you find the centroid of a composite plane lamina made of rectangles, triangles and circles? In one line Split the figure into standard shapes, find each shape's area and centroid, then take the area-weighted average of the centroids... 1
- How do you find the centroid of a lamina with holes or cut-outs using negative areas? In one line Treat the full outer shape as a positive area and each hole or cut-out as a negative area, then use the same weighted-average fo... 1
- What are the conditions of equilibrium for concurrent forces and how is Lami's theorem used? In one line Concurrent coplanar forces are in equilibrium when the sums of their x and y components are both zero; for exactly three such fo... 1
- What are the conditions of equilibrium for parallel and general coplanar forces, and how are couples balanced? In one line A body under parallel or general coplanar forces is in equilibrium only when the net force is zero and the net moment about ever... 1
- What is a free body diagram and how do you draw it correctly for equilibrium problems? In one line A free body diagram (FBD) is a sketch of the body cut free from its surroundings, showing every external force and reaction acti... 1
- What are two-force and three-force bodies and how do they simplify rigid body equilibrium? In one line A rigid body in equilibrium under only two forces needs them equal, opposite and collinear; under three non-parallel forces, the... 1
- What are the types of beams, and what is the difference between a simple and a compound beam? In one line Beams are classified by their supports into simply supported, cantilever, overhanging, fixed, propped cantilever and continuous;... 1
- What are the types of supports on beams and what reactions does each provide? In one line A support provides a reaction for every motion it stops: a roller gives one force, a hinge gives two forces, and a fixed support... 1
- How are point loads, UDL, UVL and couples on a beam converted into equivalent forces? In one line Each distributed load is replaced by a single force equal to its area acting through the centroid of the load diagram; couples a... 1
- How do you determine support reactions of a simply supported or overhanging beam? In one line Draw the FBD, replace distributed loads by equivalent point loads, then use Σ M = 0 about one support and Σ F = 0 to get the rea... 1
- How do you find the reactions and fixing moment at the fixed end of a cantilever beam? In one line At a fixed end, the vertical and horizontal reactions balance the loads, and a fixing moment balances the total moment of all lo... 1
- What are the laws of static and kinetic friction and what is the coefficient of friction? In one line Friction is the resisting force along the contact surface that opposes relative motion, and its limiting value equals the coeffi... 1
- What are the angle of friction, angle of repose and cone of friction, and how are they related? In one line The angle of friction is the angle between the total reaction and the normal at limiting friction; the angle of repose is the st... 1
- How do you find the force needed to just move a body on a rough horizontal plane? In one line Write equilibrium along and perpendicular to the plane with friction at its limiting value μ N; remember an inclined pull change... 1
- How do you analyse a body on a rough inclined plane for impending motion up or down? In one line Resolve forces along and perpendicular to the incline and put friction at μ N acting opposite to the motion that is about to occ... 1
- How do you solve a ladder friction problem resting against a wall and a floor? In one line Treat the ladder as a rigid body with normal and friction forces at floor and wall, put friction at its limiting value where sli... 1
- How do you analyse straight-line motion of a particle when acceleration varies with time? In one line When acceleration is a function of time, integrate it once to get velocity and again to get position, using the given initial co... 1
- How do you handle variable acceleration given as a function of position or velocity using v dv/dx? In one line When acceleration depends on position or velocity, use a = v dv/dx or a = dv/dt, separate the variables, and integrate. Explaine... 1
- How are velocity and acceleration of a particle on a curved path found using rectangular components? In one line Write the position as x(t) and y(t); differentiate each to get velocity and acceleration components, then combine them. Explaine... 1
- How are force systems classified into coplanar, concurrent, parallel and non-coplanar types? In one line A force system is classified by whether the forces lie in one plane and whether their lines of action meet at a point or are par... 1
- What is the principle of transmissibility of a force and what are its limits? In one line A force acting on a rigid body can be slid anywhere along its own line of action without changing its external effect on the bod... 1
- How do you resolve a force into components and combine two forces into a resultant? In one line Resolution splits one force into perpendicular parts; composition combines several forces into one equivalent force called the r... 1
- How do you find the resultant of a coplanar concurrent force system by the method of resolution? In one line Add up all horizontal components and all vertical components separately; these two sums give the size and direction of the singl... 1
- How do you find the magnitude and position of the resultant of coplanar parallel forces? In one line The resultant of parallel forces equals their algebraic sum, and its position is found by making its moment equal to the total m... 1