Engineering Mechanics
Chapters
Practice tests
See all →- MU FE Sem 1 Engineering Mechanics Most Important Questions (Winter 2026) Written paper with worked answers
- FE Sem 1 Engineering Mechanics (ESC101) Question Paper June 2025 (KT) Written paper with worked answers
- FE Sem 1 Engineering Mechanics (ESC101) Question Paper December 2025 Written paper with worked answers
Notes
See all →- System of Forces Notes FE Sem 1 Engineering Mechanics | MU MU FE Sem 1 Engineering Mechanics System of Forces notes: resultants of concurrent, parallel and general forces, moments, couples, Varignon,...
- Centroid Notes FE Sem 1 Engineering Mechanics | Mumbai University Centroid of plane laminas for MU FE Sem 1 Engineering Mechanics: standard shapes, composite and cut-out areas, T, L, I sections with solved...
- Equilibrium and Friction Notes FE Sem 1 Mechanics | Mumbai Univ MU FE Sem 1 Engineering Mechanics Module 3: equilibrium conditions, free body diagrams, beam support reactions, laws of friction, inclined p...
- Kinematics of Particles and Rigid Bodies Notes FE Sem 1 | MU MU FE Sem 1 Engineering Mechanics Module 4: variable acceleration, curvilinear motion, tangential and normal acceleration, ICR for plane mot...
- Kinetics of Particle Notes FE Sem 1 Engineering Mechanics | MU MU FE Sem 1 Engineering Mechanics Module 5: D'Alembert's principle, inertia force, impulse-momentum, restitution, direct and oblique impact.
- Robot Kinematics Notes FE Sem 1 Engineering Mechanics | MU MU FE Sem 1 Engineering Mechanics Module 6: robot basics, degrees of freedom, D-H parameters, homogeneous transformation, 2-DOF forward kine...
Top questions
See all →- Resolve the force F = 900 N acting at B as shown in Fig. into parallel components at O and A. Given: 900 N ( downarrow) at B; OA = 1 m, AB = 2 m, OB = 3 m. Let the parallel (vertical) components be F_O at O and F_A at A, both assumed... 1
- A car is made to move by applying resultant force R = 2000 N along the x-axis. This resultant is developed due to two pulling forces \(F_1\) and \(F_2\) on two ropes as shown in figure. Determine the tension in individual ropes. Method: F₁, F₂ and R form a force triangle (triangle law); apply the sine rule. The angle opposite R = 180° − 35° − 25° = 120°, so sin 120^°... 1
- Determine the force P applied at 30° to the horizontal just necessary to start a roller having 50 cm radius over a 12 cm high obstruction, if the roller is of 100 kg mass. Also find the magnitude and direction of P when it is minimum. (asked in MU De… Answer: P=648.5 N at 30°. Minimum P=637.6 N, acting at 40.54° above the horizontal (perpendicular to the line joining the corner of the step... 1
- For the overhanging beam loaded as shown, calculate the support reactions at A and B.Figure (described in words): Beam ABC is 10 m long. A (left end) is a hinged support and B is a roller support 8 m from A; BC is a 2 m overhang to the free end C. Lo… Answer: R_B=38.37 kN (upward); at A, H_A=15 kN (to the left), V_A=32.61 kN (upward), so R_A=35.89 kN at 65.3° to the horizontal (up and to t... 1
- Block A (mass 25 kg) rests on block B (mass 40 kg), which rests on a horizontal floor. A string attached to A runs up to the left to a fixed vertical wall, making 20° with the horizontal. A horizontal force P applied to B pulls it to the right. The c… Answer: P=241.4 N (string tension T=59.8 N). W_A=25×9.81=245.25 N, W_B=40×9.81=392.4 N. When B is about to move right, A is held by the stri... 1
- A planar elbow manipulator is shown. Write the D-H parameters and hence locate the position and orientation of the end E of the manipulator. Given \(L_1=L_2=250\) mm and \(\theta_1=\theta_2=30^\circ\). (asked in MU June 2025 KT)Figure (described in w… Answer: E is at (341.5,\ 341.5) mm and the end link is oriented at θ₁+θ₂=60^° to X₀. D-H parameter table (both joints revolute, all axes Z_i... 1