Engineering Mechanics
- Determine the force P applied at 30° to the horizontal just necessary to start a roller having 50 cm radius over a 12 cm high obstruction, if the roller is of 100 kg mass. Also find the magnitude and direction of P when it is minimum. (asked in MU De… Answer: P=648.5 N at 30°. Minimum P=637.6 N, acting at 40.54° above the horizontal (perpendicular to the line joining the corner of the step... 1
- For the overhanging beam loaded as shown, calculate the support reactions at A and B.Figure (described in words): Beam ABC is 10 m long. A (left end) is a hinged support and B is a roller support 8 m from A; BC is a 2 m overhang to the free end C. Lo… Answer: R_B=38.37 kN (upward); at A, H_A=15 kN (to the left), V_A=32.61 kN (upward), so R_A=35.89 kN at 65.3° to the horizontal (up and to t... 1
- Block A (mass 25 kg) rests on block B (mass 40 kg), which rests on a horizontal floor. A string attached to A runs up to the left to a fixed vertical wall, making 20° with the horizontal. A horizontal force P applied to B pulls it to the right. The c… Answer: P=241.4 N (string tension T=59.8 N). W_A=25×9.81=245.25 N, W_B=40×9.81=392.4 N. When B is about to move right, A is held by the stri... 1
- A planar elbow manipulator is shown. Write the D-H parameters and hence locate the position and orientation of the end E of the manipulator. Given \(L_1=L_2=250\) mm and \(\theta_1=\theta_2=30^\circ\). (asked in MU June 2025 KT)Figure (described in w… Answer: E is at (341.5,\ 341.5) mm and the end link is oriented at θ₁+θ₂=60^° to X₀. D-H parameter table (both joints revolute, all axes Z_i... 1
- A three-link planar (3R) robot arm has link lengths \(L_1=0.5\) m, \(L_2=0.4\) m and \(L_3=0.2\) m. At an instant the joint angles are \(\theta_1=30^\circ\) (link 1 measured anticlockwise from the base \(X_0\) axis), \(\theta_2=45^\circ\) and \(\thet… Answer: End effector at (0.678,\ 0.778) m, oriented at 45^° to X₀. D-H table (all joints revolute about axes perpendicular to the plane: d_i... 1
- The acceleration of a particle in rectilinear motion is given by \(a=64-4x^2\ \text{m/s}^2\), where x is in metres. At \(x=0\) the particle is at rest. Find the velocity at \(x=3\) m, and the position and value of the maximum velocity. Answer: v=17.66 m/s at x=3 m; maximum velocity =18.48 m/s at x=4 m. Since a is given as a function of x, use a=vdv/dx: ∫₀^v v dv=∫₀^x(64-4x²... 1
- The position vector of a particle moving in the X–Y plane is \(\vec r=(2t^3-3t)\,\hat i+(t^2+4)\,\hat j\) m, where t is in seconds. At \(t=2\) s, find (i) the velocity and acceleration, (ii) the tangential and normal components of acceleration, and (… Answer: vec v=21hat i+4hat j (21.38 m/s), vec a=24hat i+2hat j (24.08 m/s²); a_t=23.95 m/s², a_n=2.53 m/s²; ρ=180.9 m. (i) vec v=(dvec r)/dt... 1
- In the mechanism shown, the angular velocity of link AB is 5 rad/s anticlockwise. At the instant shown, determine the angular velocity of link BC and the velocity of piston C. (asked in MU Dec 2025)Figure (described in words): Link AB hangs verticall… Answer: ω_BC=6.67 rad/s (clockwise); v_C=3 m/s, vertically downward. Velocity of B: A is fixed and AB is vertical, so B moves perpendicular... 1
- Collar B moves up a fixed vertical rod with a constant velocity of 3 m/s. Rod AB, 2 m long, is pinned to the collar at B and makes 45° with the horizontal at B, running down to the left to end A. End A slides on a fixed surface inclined at 30° to the… Answer: ω_AB=1.345 rad/s (anticlockwise); v_A=2.20 m/s up the incline (at 30° to the horizontal); v_G=2.26 m/s. Directions of velocities: v_... 1
- A cricket ball of mass 0.16 kg moving horizontally at 25 m/s is hit straight back by a bat and leaves at 35 m/s. If the bat is in contact with the ball for 0.02 s, find the impulse and the average force exerted by the bat. Answer: Impulse =9.6 N s; average force =480 N (both directed opposite to the ball's initial motion). Take the direction of the returning ba... 1
- Explain with neat sketches (1) direct central impact and (2) oblique central impact. (asked in MU June 2025 KT) Answer: In both cases the line of impact passes through the mass centres of the bodies. In direct central impact the velocities are along th... 1
- The system shown is initially at rest. Neglecting friction, determine the force P required if the velocity of collar B is 5 m/s after 2 s, and the corresponding tension in the cable. (asked in MU Dec 2025; also June 2025 KT)Figure (described in words… Answer: P=51.93 N; cable tension T=22.22 N. Kinematic relation. Let x_B be the distance of collar B from the wall and y_A the depth of block... 1
- A 4 kg block rests on a plane inclined at 20° to the horizontal. The coefficient of kinetic friction is 0.25. A variable force \(P=(2t+5)\) N, where t is in seconds, acts on the block parallel to the plane, pointing down the slope. If the block start… Answer: v=13.2 m/s down the plane. W=4×9.81=39.24 N. Component of W down the plane =39.24sin20^°=13.42 N; normal reaction N=39.24cos20^°=36.... 1
- A 60 kg crate rests on a horizontal floor for which the coefficient of kinetic friction is 0.25. It is pulled by a force of 400 N acting at 25° above the horizontal. Assuming the crate does not tip over, find its velocity 5 s after starting from rest… Answer: v=21.47 m/s. Forces: W=60×9.81=588.6 N. Vertical: N+400sin25^°=588.6⇒ N=588.6-169.05=419.55 N (the upward pull reduces the normal re... 1
- Find the coordinates of the centroid of the shaded lamina with respect to the given reference axes.Figure (described in words): Origin O at the bottom-left corner, x-axis to the right, y-axis upward; dimensions in cm. The lamina is made of: a rectang… Answer: bar x=4.82 cm, bar y=4.36 cm. PartArea A (cm²) x (cm) y (cm) Ax Ay 1. Rectangle 8 × 64843192144 2. Semicircle, r=4 π(4)²/2=25.13 4 6... 1
- Find the coordinates of the centroid of the shaded area with respect to the given reference axes.Figure (described in words): Origin O, x-axis to the right, y-axis upward; dimensions in cm. In the first quadrant there is a quarter circle of radius 6… Answer: bar x=0.43 cm, bar y=2.57 cm. PartArea A (cm²) x (cm) y (cm) Ax Ay 1. Quarter circle, R=6 π(6)²/4=28.27 4R/3π=2.546 2.54672.0072.00... 1
- Prove that angle of friction is equal to angle of repose. (asked in MU Dec 2025) Answer: On an inclined plane at the angle of repose α, tanα=F/N=μ=tanφ, so α=φ. Definitions. Angle of friction φ: the angle between the norm... 1
- A 40 kg block hangs from joint B. Cord BA goes up to the left to a fixed support A, making 35° with the horizontal at B, and cord BC goes up to the right to a fixed support C, making 50° with the horizontal at B. Determine the tensions in cords AB an… Answer: T_AB=253.2 N, T_BC=322.7 N. Weight W=40×9.81=392.4 N. FBD of joint B: T_AB up-left at 35°, T_BC up-right at 50°, W downward. Σ F_x=0... 1
- A force of magnitude 60 kN acts at point A(1, 2, 3) m and is directed towards point B(4, −2, 15) m. Find the components of the force along the X, Y and Z axes and write it in vector form. Answer: vec F=13.85 hat i-18.46 hat j+55.38 hat k kN, i.e. F_x=13.85 kN, F_y=-18.46 kN, F_z=55.38 kN. Position vector from A to B: overright... 1
- A force of 40 N acts at point P(2, 1, 3) m. The force makes angles of 60° and 45° with the X and Y axes respectively, and has a positive Z component. Express the force in vector form. Answer: vec F=20 hat i+28.28 hat j+20 hat k N ( θ_z=60^° ). Direction cosines satisfy cos²θ_x+cos²θ_y+cos²θ_z=1. cos²θ_z=1-cos²60^°-cos²45^°... 1
- A boat is pulled along a straight canal by two ropes, so that the resultant pull is 1500 N along the canal (the x-axis). Rope 1 makes 30° above the x-axis and rope 2 makes 20° below the x-axis, both pulling forward. Find the tension in each rope. Answer: T₁=669.7 N, T₂=979.1 N. The resultant has no y-component, so Σ F_y=0:\ T₁sin30^°-T₂sin20^°=0 ...(1) Σ F_x=1500:\ T₁cos30^°+T₂cos20^°... 1
- A rectangular plate OBCD is 4 m long (OB, along the x-axis) and 3 m high (OD, along the y-axis). Determine the magnitude and direction of the resultant of the force system acting on it, and locate the point where the resultant cuts the x-axis (line O… Answer: R=170.3 N at θ=40.24^° above the +x direction (up and to the right); it cuts the x-axis at 4.55 m to the right of O. Take O as origi... 1
- What are the basic parts of a robot manipulator: links, joints, end effector and workspace? In one line A robot manipulator is a chain of rigid links connected by joints, starting at a fixed base and ending at an end effector that d... 1
- What is degree of freedom of a robot and how is it counted for a serial manipulator? In one line Degree of freedom (DOF) is the number of independent variables needed to fully describe a robot's configuration; for a serial ro... 1