Engineering Mechanics
- Determine the force P applied at 30° to the horizontal just necessary to start a roller having 50 cm radius over a 12 cm high obstruction, if the roller is of 100 kg mass. Also find the magnitude and direction of P when it is minimum. Given: W = 100 × 9.81 = 981 N, r = 50 cm, h = 12 cm. When the roller is just about to climb, the floor reaction becomes zero; the forces are... 1
- Find the force P required to pull block B shown in figure. Coefficient of friction between A and B is 0.3 and between B and floor is 0.25. Mass of A = 20 kg and B = 30 kg. Given: W_A = 20 × 9.81 = 196.2 N, W_B = 30 × 9.81 = 294.3 N, μ₁ = 0.3 (A–B), μ₂ = 0.25 (B–floor). A is held by the string; B is about to mov... 1
- For the beam loaded as shown in figure, Calculate the support reactions. Loads: UDL resultant = 10 × 2 = 20 kN at 1 m from A. Inclined 20 kN: vertical component 20sin60^° = 17.32 kN (↓), horizontal component 20cos... 1
- A simple 2 DOF planar robot is shown. Prepare a D H parameter table and perform forward kinematics to find the location and orientation of end effector B. Joint angles: θ₁ = 110^°; θ₂ = -65^° (measured clockwise from the extension of link 1). Link 2 absolute angle = θ₁ + θ₂ = 45^°. Link i θ_i d... 1
- The acceleration of the particle is defined by the relation \(a = 25 - 3x^2\ \text{mm/s}^2\). The particle starts with no initial velocity at the position x = 0. Determine the position where the velocity is maximum and the corresponding maximum veloc… Using vdv/dx = a: displaystyle∫₀^v v dv = ∫₀^x (25 - 3x²) dx ⇒ v²/2 = 25x - x³ Maximum velocity when dv/dx = 0, i.e. when a = 0: 25 - 3x² =... 1
- The motion of a particle is defined by the position vector, \(\bar r = 5t\,i + 3t^2\,j\) where ‘r’ is in meters and t is in seconds. At the instant when t = 2 sec, find i) Tangential and normal components of accelerations ii) Radius of curvature. bar v = 5 i + 6t j; at t = 2 s: bar v = 5 i + 12 j, v = √(25 + 144) = 13 m/s bar a = 6 j m/s² (constant), a = 6 m/s² i) Tangential component... 1
- In the mechanism shown in fig, the angular velocity of link AB is 5 rad/sec anticlockwise. At the instant shown, determine the angular velocity of link BC and velocity of piston C. Velocity of B: v_B = ω_AB × AB = 5 × 0.2 = 1 m/s, perpendicular to AB. With B directly below A and AB rotating anticlockwise, v_B is horizon... 1
- The system shown in figure is initially at rest. Neglecting friction determine the force ‘P’ required if the velocity of the collar B is 5 m/s after 2 sec and corresponding tension in the cable. Given: m_B = 3 kg, m_A = 1.5 kg, system starts from rest, v_B = 5 m/s after t = 2 s, all surfaces and pulleys frictionless. 1. Constraint (k... 1
- A 3 kg mass kept on a 30° slope is subjected to a variable force \(P = (t^2 + 3)\), where P is in ‘Newton’ and t is in ‘second’ find velocity of the block after 5 second using Impulse momentum principle. At t = 0, V = 0. Given: m = 3 kg, W = 29.43 N, μ = 0.2, P = t² + 3 N down the slope, u = 0. The block moves down the slope, so friction acts up the slope. N... 1
- A car is made to move by applying resultant force R = 2000 N along the x-axis. This resultant is developed due to two pulling forces \(F_1\) and \(F_2\) on two ropes as shown in figure. Determine the tension in individual ropes. Method: F₁, F₂ and R form a force triangle (triangle law); apply the sine rule. The angle opposite R = 180° − 35° − 25° = 120°, so sin 120^°... 1
- A force 30 N is acting at point P(3, 2, 1) m. The force makes 35° & 85° with x & y axes respectively. Express the force in vector form. Direction cosines satisfy cos²θ_x + cos²θ_y + cos²θ_z = 1: cos²θ_z = 1 - cos² 35^° - cos² 85^° = 1 - 0.6710 - 0.0076 = 0.3214 ⇒ cosθ_z = 0.5... 1
- A system of forces acting on a bell crank is as shown in fig. Determine the magnitude, direction and the point of application of the resultant w.r.t. O. Axes: O origin, x right, y up; forces in N, distances in mm. ForcePoint (x, y) F_x F_y M_O = xF_y - yF_x 500 N(−300, 0)+250−433.01+129 904 1... 1
- Three right circular cylinders A, B and C are piled up in a rectangular channel as shown in figure. Answer: Reaction at point 6 (between cylinder A and the left wall) R₆ = 80\ kgf = 784.8\ N, acting horizontally. Data from the figure: chann... 1
- Two spheres A & B of weight 1000 N and 750 N respectively are kept as shown in the figure. Answer: R₁ = 496.6\ N, R₂ = 1463.3\ N, R₃ = 869.1\ N, R₄ = 573.5\ N. Data from the figure: sphere B (750 N, r = 300 mm) sits on the horizont... 1
- Determine the reaction points at constant 1,2 & 3. Assume smooth surfaces. Answer: R₁ = 19.75\ N, R₂ = 11.62\ N (line AB at 44.1^° to the horizontal), R₃ = 32.25\ N. (The question means the reactions at the contact... 1
- A cylinder weighing 1000 N and 1.5 m diameter is supported by a beam AB of length 6 m and weight 400 N Answer: Wall reaction at D R_D = 1000\ N (horizontal), tension in cable BC T ≈ 588.2\ N, hinge reaction at A R_A ≈ 1209.8\ N at 66.1^° to th... 1
- Determine the resultant of the given system of forces shown in fig find the point of application of resultant with https://lh3.googleusercontent.com/-EZSQfz4EX-U/YdxEse4QEQI/AAAAAAAADHk/XhlWZPW1EvggU9rL3qygoXevY-dIYsgfwCNcBGAsYHQ/image.png Refer img for a... 1
- A rigid bar is subjected to a system of parallel forces as shown. Reduce this system to 1) A single force https://lh3.googleusercontent.com/-JesrlokgTgg/YdxChWvhOYI/AAAAAAAADHU/fPe84GnbvRg1ovYRKLZQB0xk3XLxVD9dQCNcBGAsYHQ/image.png Refer img for a... 1
- A ring is pulled by three forces as shown in figure. Find the force F and the angle θ if resultant of these three forces θ=47.6^o 1
- The striker of carom board lying on the board is being pulled by four players as shown in the figure. R=29.09 N and θ =45.89^o https://lh3.googleusercontent.com/-UxqeJC9QNZ4/Ydv8lhg3S3I/AAAAAAAADGw/gze9dw27U5M0hKlTDhzoaeGIsOuY3WHPgCNcBGAsYHQ/... 1